Delete printer_data/config directory
This commit is contained in:
admin authored and 
GitHub committed
1 parent
41ba23272c
commit
4b8cb5e9ec
14 files changed
-2273
No files matched your search
@@ -1,523 +0,0 @@
|
||||
# This file contains common pin mappings for the BigTreeTech OctoPus V1.
|
||||
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
||||
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
||||
|
||||
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
||||
|
||||
## *** THINGS TO CHANGE/CHECK: ***
|
||||
## MCU paths [mcu] section
|
||||
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||
## Z Endstop Switch location [safe_z_home] section
|
||||
## Homing end position [gcode_macro G32] section
|
||||
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||
## Probe points [quad_gantry_level] section
|
||||
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||
## PID tune [extruder] and [heater_bed] sections
|
||||
## Fine tune E steps [extruder] section
|
||||
|
||||
[include ./SYSTEM/*.cfg]
|
||||
[include ./TOOLHEAD/*.cfg]
|
||||
[include ./CUSTOM/*.cfg]
|
||||
|
||||
[mcu]
|
||||
## [X in MOTOR0] - B Motor
|
||||
## [Y in MOTOR1] - A Motor
|
||||
## [E in MOTOR6] - Extruder
|
||||
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
||||
##--------------------------------------------------------------------
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_360026001950534146373920-if00
|
||||
restart_method: command
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 500
|
||||
max_accel: 4200 #Max 4000
|
||||
#max_y_accel: 4200
|
||||
#max_x_accel: 8000
|
||||
#max_accel: 10000 #Testing - revert back to above line after!
|
||||
#max_accel_to_decel: 10000 #Testing - revert back to above line after!
|
||||
max_z_velocity: 30 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_z_accel: 500
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
[force_move]
|
||||
enable_force_move: True
|
||||
|
||||
[skew_correction]
|
||||
[exclude_object]
|
||||
[firmware_retraction]
|
||||
[gcode_arcs]
|
||||
resolution: 0.1
|
||||
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## X Stepper on MOTOR0(B Motor)
|
||||
[stepper_x]
|
||||
step_pin: PF13
|
||||
dir_pin: PF12
|
||||
enable_pin: !PF14
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
||||
position_min: 0
|
||||
position_endstop: 352
|
||||
position_max: 352
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 50 #Max 100
|
||||
homing_retract_dist: 0
|
||||
homing_positive_dir: true
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC4
|
||||
interpolate: False
|
||||
run_current: 0.9
|
||||
hold_current: 0.7
|
||||
sense_resistor: 0.110
|
||||
#stealthchop_threshold: 400
|
||||
diag_pin: ^PG6
|
||||
driver_SGTHRS: 60 #255 Most Sensitive 0 Least Sensitive
|
||||
|
||||
## Y Stepper on MOTOR1 (A Motor)
|
||||
[stepper_y]
|
||||
step_pin: PG0
|
||||
dir_pin: PG1
|
||||
enable_pin: !PF15
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
||||
position_min: 0
|
||||
position_endstop: 359
|
||||
position_max: 359
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 50 #Max 100
|
||||
homing_retract_dist: 0
|
||||
homing_positive_dir: true
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PD11
|
||||
interpolate: False
|
||||
run_current: 0.9
|
||||
hold_current: 0.7
|
||||
sense_resistor: 0.110
|
||||
#stealthchop_threshold: 400
|
||||
diag_pin: ^PG9
|
||||
driver_SGTHRS: 63 #255 Most Sensitive 0 Least Sensitive
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left on MOTOR2_1
|
||||
[stepper_z]
|
||||
step_pin: PF9
|
||||
dir_pin: PF10
|
||||
enable_pin: !PG2
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
endstop_pin: EBB:gpio6
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
#position_endstop: -0.5
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_max: 240
|
||||
|
||||
## Uncomment below for 300mm build
|
||||
#position_max: 290
|
||||
|
||||
## Uncomment below for 350mm build
|
||||
position_max: 300
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
position_min: -2
|
||||
homing_speed: 15
|
||||
second_homing_speed: 1
|
||||
homing_retract_dist: 3
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PF2
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left on MOTOR3
|
||||
[stepper_z1]
|
||||
step_pin: PC13
|
||||
dir_pin: !PF0
|
||||
enable_pin: !PF1
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z1]
|
||||
uart_pin: PE4
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right on MOTOR4
|
||||
[stepper_z2]
|
||||
step_pin: PE2
|
||||
dir_pin: PE3
|
||||
enable_pin: !PD4
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z2]
|
||||
uart_pin: PE1
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right on MOTOR5
|
||||
[stepper_z3]
|
||||
step_pin: PE6
|
||||
dir_pin: !PA14
|
||||
enable_pin: !PE0
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z3]
|
||||
uart_pin: PD3
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
## SSR Pin - BED_OUT
|
||||
heater_pin: PA1
|
||||
sensor_type: Generic 3950
|
||||
sensor_pin: PF3
|
||||
## Adjust Max Power so your heater doesn't warp your bed
|
||||
max_power: 1.0
|
||||
min_temp: 0
|
||||
max_temp: 125
|
||||
#control: pid
|
||||
#pid_kp: 58.437
|
||||
#pid_ki: 2.347
|
||||
#pid_kd: 363.769
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
## Part Cooling Fan - CPAP 7040
|
||||
pin: PG15
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.05
|
||||
hardware_pwm: False
|
||||
cycle_time: 0.005
|
||||
off_below: 0.1
|
||||
|
||||
|
||||
[controller_fan stepper_fan]
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: PD12
|
||||
max_power: 0.9
|
||||
kick_start_time: 0.5
|
||||
fan_speed: 0.7
|
||||
|
||||
[controller_fan electronic_chamber_fans]
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: PD13
|
||||
max_power: 0.8
|
||||
kick_start_time: 0.5
|
||||
fan_speed: 0.4
|
||||
|
||||
|
||||
[temperature_fan exhaust_fan]
|
||||
pin: PE5
|
||||
shutdown_speed: 0.0
|
||||
kick_start_time: 5.0
|
||||
cycle_time: 0.05
|
||||
hardware_pwm: True
|
||||
off_below: 0.15
|
||||
|
||||
sensor_type: temperature_combined
|
||||
sensor_list: temperature_sensor _chamber_1, temperature_sensor _chamber_2, temperature_sensor _chamber_3, temperature_sensor _chamber_4
|
||||
combination_method: mean
|
||||
maximum_deviation: 999
|
||||
|
||||
control: pid
|
||||
pid_Kp: 35.0
|
||||
pid_Ki: 12
|
||||
pid_Kd: 4.0
|
||||
pid_deriv_time: 2.0
|
||||
|
||||
target_temp: 50.0
|
||||
min_temp: 0
|
||||
max_temp: 110
|
||||
min_speed: 0.149
|
||||
max_speed: 1.0
|
||||
|
||||
gcode_id: C
|
||||
|
||||
#[temperature_fan exhaust_fan]
|
||||
## Exhaust fan - CNC_FAN3
|
||||
#pin: PE5
|
||||
#max_power: 1.0
|
||||
#shutdown_speed: 0.0
|
||||
#kick_start_time: 5.0
|
||||
#cycle_time:0.05
|
||||
#off_below:0.1
|
||||
#sensor_type: temperature_combined
|
||||
#sensor_list: temperature_sensor _chamber_1,temperature_sensor _chamber_2,temperature_sensor _chamber_3,temperature_sensor _chamber_4
|
||||
#combination_method: mean
|
||||
#maximum_deviation: 999
|
||||
#min_temp: 0
|
||||
#max_temp: 80
|
||||
#target_temp: 35.0
|
||||
#max_delta: 0.5
|
||||
#max_speed: 1.0
|
||||
#min_speed: 0.3
|
||||
#control: watermark
|
||||
#gcode_id: C
|
||||
|
||||
[gcode_macro M141]
|
||||
gcode:
|
||||
{% set s = params.S|default(0)|float %}
|
||||
SET_TEMPERATURE_FAN_TARGET temperature_fan="exhaust_fan" target={s}
|
||||
|
||||
[fan_generic nevermore_fan]
|
||||
pin: PD15
|
||||
max_power: 1.0
|
||||
kick_start_time: 1.0
|
||||
cycle_time: 0.05
|
||||
off_below: 0.13
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
#[output_pin caselight]
|
||||
# Chamber Lighting - HE1 Connector (Optional)
|
||||
#pin: PB11
|
||||
#pwm:true
|
||||
#shutdown_value: 0
|
||||
#value:1
|
||||
#cycle_time: 0.01
|
||||
|
||||
[output_pin daylight]
|
||||
pin: PB11
|
||||
pwm: True
|
||||
cycle_time: 0.01
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
|
||||
#[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||
## (such as 157,305) after going through Z Endstop Pin
|
||||
## Location Definition step.
|
||||
#home_xy_position:175,175
|
||||
#speed:100
|
||||
#z_hop:10
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||
## to respective belt positions
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
## Gantry Corners for 250mm Build
|
||||
## Uncomment for 250mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 310, 320
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,175
|
||||
# 200,175
|
||||
# 200,25
|
||||
|
||||
## Gantry Corners for 300mm Build
|
||||
## Uncomment for 300mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 360,370
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,225
|
||||
# 250,225
|
||||
# 250,25
|
||||
|
||||
## Gantry Corners for 350mm Build
|
||||
## Uncomment for 350mm build
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
410,420
|
||||
# Probe points
|
||||
points:
|
||||
50,25
|
||||
50,275
|
||||
300,275
|
||||
300,25
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
speed: 200
|
||||
horizontal_move_z: 2
|
||||
retries: 15
|
||||
retry_tolerance: 0.015
|
||||
max_adjust: 5
|
||||
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
[neopixel front_logo]
|
||||
|
||||
pin: PB0
|
||||
# The pin connected to the neopixel. This parameter must be
|
||||
# provided.
|
||||
chain_count: 7
|
||||
# The number of Neopixel chips that are "daisy chained" to the
|
||||
# provided pin. The default is 1 (which indicates only a single
|
||||
# Neopixel is connected to the pin).
|
||||
color_order: GRB
|
||||
# Set the pixel order required by the LED hardware (using a string
|
||||
# containing the letters R, G, B, W with W optional). Alternatively,
|
||||
# this may be a comma separated list of pixel orders - one for each
|
||||
# LED in the chain. The default is GRB.
|
||||
initial_RED: 1.0
|
||||
initial_GREEN: 0.0
|
||||
initial_BLUE: 0.0
|
||||
initial_WHITE: 0.0
|
||||
# See the "led" section for information on these parameters.
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
|
||||
[gcode_macro G32]
|
||||
description: Home XYZ mesh calibrate
|
||||
gcode:
|
||||
STATUS_HOMING
|
||||
BED_MESH_CLEAR
|
||||
G28
|
||||
QUAD_GANTRY_LEVEL
|
||||
G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } F4500
|
||||
|
||||
STATUS_MESHING
|
||||
BED_MESH_CALIBRATE METHOD=rapid_scan
|
||||
G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } Z30 F4500
|
||||
STATUS_READY
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
[gcode_macro FAST_CALIBRATE]
|
||||
description: Quickly home axis and mesh area to be printed. QGL if needed
|
||||
gcode:
|
||||
BED_MESH_CLEAR
|
||||
_CG28
|
||||
{% if printer.quad_gantry_level.applied|lower == 'false' %}
|
||||
STATUS_LEVELING
|
||||
QUAD_GANTRY_LEVEL
|
||||
{% endif %}
|
||||
G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } F4500
|
||||
|
||||
STATUS_MESHING
|
||||
BED_MESH_CALIBRATE ADAPTIVE=1 METHOD=rapid_scan
|
||||
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||
gcode:
|
||||
CLEAN_NOZZLE
|
||||
STATUS_PRINTING
|
||||
LINE_PURGE
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-10.0 F3600 ; retract filament
|
||||
G91 ; relative positioning
|
||||
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||
TURN_OFF_HEATERS
|
||||
M107 ; turn off fan
|
||||
M106 S0
|
||||
G1 Z5 F3000 ; move nozzle up 5mm
|
||||
G90 ; absolute positioning
|
||||
BED_MESH_CLEAR
|
||||
SET_PIN PIN=daylight VALUE=0.0
|
||||
|
||||
## Thermistor Types
|
||||
## "EPCOS 100K B57560G104F"
|
||||
## "ATC Semitec 104GT-2"
|
||||
## "NTC 100K beta 3950"
|
||||
## "Honeywell 100K 135-104LAG-J01"
|
||||
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
||||
## "AD595"
|
||||
## "PT100 INA826"
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 15.921
|
||||
#*# pid_ki = 3.553
|
||||
#*# pid_kd = 12.717
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 38.431
|
||||
#*# pid_ki = 1.601
|
||||
#*# pid_kd = 230.586
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*# position_endstop = -0.65
|
||||
#*#
|
||||
#*# [input_shaper]
|
||||
#*# shaper_type_x = mzv
|
||||
#*# shaper_freq_x = 52.2
|
||||
#*# shaper_type_y = mzv
|
||||
#*# shaper_freq_y = 37.8
|
||||
Reference in new issue
Block a user