New backup from 18/04/25 - 08:36:31

2025-04-18 08:36:31 +01:00
1 parent 4b8cb5e9ec
commit 776f43b3f4
@@ -0,0 +1,132 @@
+[bed_mesh]
+mesh_min = 15, 25
+mesh_max = 330, 330
+speed = 300
+horizontal_move_z = 2
+probe_count = 30,30
+algorithm = bicubic
+split_delta_z = 0.0125
+scan_overshoot: 5
+zero_reference_position: 176.00,179.50
+fade_start: 1.0
+fade_end: 10.0
+fade_target: 0.0
+##[(7x7)-1] / 2 = 24
+##[(5x5)-1] / 2 = 12
+##[(9x9)-1] / 2 = 40
+#relative_reference_index: 40
+#relative_reference_index: 15
+
+
+[gcode_macro QUAD_GANTRY_LEVEL]
+rename_existing: _QUAD_GANTRY_LEVEL
+gcode:
+    STATUS_LEVELING
+    SAVE_GCODE_STATE NAME=STATE_QGL
+    BED_MESH_CLEAR
+    # If QGL has not been done yet, correct for any major skew first
+    # at 8mm height
+    {% if not printer.quad_gantry_level.applied %}
+    _QUAD_GANTRY_LEVEL horizontal_move_z=8 retry_tolerance=1      
+    {% endif %}
+    # Compelte with a full QGL at the configured height
+    _QUAD_GANTRY_LEVEL
+    RESTORE_GCODE_STATE NAME=STATE_QGL
+
+
+[gcode_macro BED_MESH_CALIBRATE]
+rename_existing: _BED_MESH_CALIBRATE
+gcode:
+    {% set TARGET_TEMP = printer.heater_bed.target %}
+    M140 S0
+    _BED_MESH_CALIBRATE {rawparams}
+    M140 S{TARGET_TEMP}
+
+[gcode_macro CARTOGRAPHER_TOUCH]
+rename_existing: _CARTOGRAPHER_TOUCH
+gcode:
+    {% set TARGET_TEMP = printer.heater_bed.target %}
+    M140 S0
+    _CARTOGRAPHER_TOUCH {rawparams}
+    M140 S{TARGET_TEMP}
+
+#####################################################################
+#  Macros
+#####################################################################
+## customize BED MESH CALIBRATE gcode 
+
+## use BED_MESH_STORE                       -> generate MESH and save immediately and park in the middle
+## use BED_MESH_STORE PARK=false            -> generate MESH and save immediately  
+## use BED_MESH_STORE SAVE=false            -> generate MESH and save it later
+## use BED_MESH_STORE SAVE=false PARK=false -> would be most likely be used in your macros
+[gcode_macro BED_MESH_STORE]
+description: Generate a mesh, name it and run save_config if requested
+variable_save_at_end: 'false' 
+gcode:
+  ##### set default parameter value #####
+  {% set save = params.SAVE|default('true') %}
+  {% set park = params.PARK|default('true') %}
+  #############  Get user defines  #############
+  {% set center = printer["gcode_macro _USER_VARIABLE"].center %}
+  {% set z_hop = printer["gcode_macro _USER_VARIABLE"].z_hop %}
+  {% set bed_temp = printer.heater_bed.target|int %}
+  ##### define plate name: Voron (default) or flexplate name #####
+  {% set plate_name = 'Voron' %}
+  {% if 'save_variables' in printer.configfile.config %}
+    {% if printer.save_variables.variables.plate_array is defined %}
+      {% set plate_index = printer.save_variables.variables.plate_index|int %}
+      {% set plate_name = printer.save_variables.variables.plate_array[plate_index][0] %}
+    {% endif %}
+  {% endif %}
+  ##### join everything to a single mesh name #####
+  {% set mesh_name = "Voron-Bed_Temp-" + bed_temp|string + "C" %}
+  ##### end of definitions #####
+  BED_MESH_CALIBRATE
+  BED_MESH_PROFILE SAVE={mesh_name}
+  BED_MESH_PROFILE REMOVE=default
+  {% if park|lower == 'true' %}
+    G90                                ; set absolute
+    G0 Z{z_hop} F1800            ; move nozzle to z high first
+    G0 X{center[0]} Y{center[1]} F18000  ; home to get toolhead in the middle
+  {% endif %}
+  {% if save|lower == 'true' %}
+    _PRINT_AR T="BED_MESH: Save Config!"
+    SAVE_CONFIG
+  {% else %}
+    _PRINT_AR T="BED_MESH: Save Config after print done"
+    SET_GCODE_VARIABLE MACRO=BED_MESH_STORE VARIABLE=save_at_end VALUE='"true"'
+  {% endif %}
+
+
+## use BED_MESH_LOAD           -> load an existing MESH
+## use BED_MESH_LOAD AUTO=true -> load an existing MESH or generate a new one and prepare it to be saved after print end
+[gcode_macro BED_MESH_LOAD]
+description: Load an existing mesh or generate a new one
+gcode:
+  ##### set default parameter value #####
+  {% set auto = params.AUTO|default('false') %}
+  {% set bed_temp = printer.heater_bed.target|int %}
+  ##### join everything to a single mesh name #####
+  {% set mesh_name = "Voron-Bed_Temp-" + bed_temp|string + "C" %}
+  ##### end of definitions #####
+  {% if printer.configfile.config["bed_mesh " + mesh_name] is defined %}
+    BED_MESH_CLEAR
+    BED_MESH_PROFILE LOAD={mesh_name}
+    _PRINT_AR T="{"BED_MESH: " + mesh_name + " loaded"}"
+  {% else %}
+    {% if auto|lower == 'true' %}
+      _PRINT_AR T="{"BED_MESH: " + mesh_name + " needs to be generated"}"
+      BED_MESH_STORE SAVE=false PARK=false
+    {% else %}
+      _PRINT_AR T="{"BED_MESH ERROR: " + mesh_name + " not defined"}"
+    {% endif %}
+  {% endif %}
+
+## add this to your PRINT_END to save a mesh if needed 10 seconds after print ended
+## UPDATE_DELAYED_GCODE ID=_BED_MESH_SAVE DURATION=10
+[delayed_gcode _BED_MESH_SAVE]
+gcode:
+  {% if printer["gcode_macro BED_MESH_STORE"].save_at_end == 'true'  %}
+    _PRINT_AR T="BED_MESH: Save Config!"
+    SAVE_CONFIG
+  {% endif %}
@@ -0,0 +1,95 @@
+# Note you may need to add the following to your printer.cfg somewhere (without the comments of course) for the Kinematic position stuff below to work.
+#[force_move]
+#enable_force_move: True
+
+#[safe_z_home]
+#home_xy_position: 175, 175
+#speed: 150.0
+#z_hop: 2
+#z_hop_speed: 15.0
+#move_to_previous: False
+
+[gcode_macro _HOME_X]
+gcode:
+    # Home
+    {% set RUN_CURRENT_X = printer.configfile.settings['tmc2209 stepper_x'].run_current|float %}
+    {% set RUN_CURRENT_Y = printer.configfile.settings['tmc2209 stepper_y'].run_current|float %}
+    {% set HOME_CURRENT = 0.49 %}
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CURRENT}
+    SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CURRENT}
+    
+    SET_KINEMATIC_POSITION X=5
+    G91
+    G1 X-5 F1200
+    
+    #G4 P2000
+    #M400 to finish all pending moves/process the buffer
+    M400 
+    G28 X
+    
+    # Move away
+    G91
+    G1 X-5 F1200
+    
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CURRENT_X}
+    SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CURRENT_Y}
+
+[gcode_macro _HOME_Y]
+gcode:
+    {% set RUN_CURRENT_X = printer.configfile.settings['tmc2209 stepper_x'].run_current|float %}
+    {% set RUN_CURRENT_Y = printer.configfile.settings['tmc2209 stepper_y'].run_current|float %}
+    {% set HOME_CURRENT = 0.49 %}
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CURRENT}
+    SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CURRENT}
+    
+    SET_KINEMATIC_POSITION Y=5
+    G91
+    G1 Y-5 F1200
+    
+    #G4 P2000
+    #M400 to finish all pending moves/process the buffer
+    M400 
+    
+    # Home
+    G28 Y
+    # Move away
+    G91
+    G1 Y-5 F1200
+
+    # Wait just a second… (give StallGuard registers time to clear)
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CURRENT_X}
+    SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CURRENT_Y}
+
+[homing_override]
+axes: xyz
+gcode:
+  {% set home_all = 'X' not in params and 'Y' not in params and 'Z' not in params %}
+
+  SET_KINEMATIC_POSITION Z=0
+  G1 Z5 F1200
+
+  {% if home_all or 'X' in params %}
+    _HOME_X
+  {% endif %}
+  
+  {% if home_all or 'Y' in params %}
+    _HOME_Y
+  {% endif %}
+  
+  {% if home_all or 'Z' in params %}
+
+    G90
+    G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } F4500
+
+    G28 Z
+
+    G1 Z10 F1500
+  {% endif %}
+
+
+[gcode_macro _CG28]
+description: Homing only if necessary
+gcode:
+    {% if "xyz" not in printer.toolhead.homed_axes %}
+        G28
+    {% endif %}
@@ -0,0 +1,696 @@
+[gcode_macro SET_MATERIAL]
+description: Dynamically adjust chamber temps, fans, and behavior based on material
+
+# === OVERVIEW ===
+# This macro sets print parameters based on the selected filament type.
+# It includes logic for fan control, pressure advance tuning, and chamber temperature management.
+# Each material is uniquely handled with comments, proper defaults, and warnings where applicable.
+#
+# === WHY USE THIS ===
+# - Ensures consistent print settings per material
+# - Automatically adjusts temperature and environment conditions
+# - Reduces manual tuning between material changes
+# - Helps enforce safety (drying warnings, chamber heat warnings, etc.)
+#
+# === HOW TO USE ===
+# Call the macro with:
+#   SET_MATERIAL MATERIAL=<your_material>
+#
+# Example:
+#   SET_MATERIAL MATERIAL=ABS
+#
+# === SETUP REQUIREMENTS ===
+# You MUST configure:
+# - A chamber temperature sensor (e.g., temperature_sensor chamber_combined_mean)
+# - A bed heater (e.g., heater_bed)
+# - Optionally, a chamber heater (e.g., heater_generic chamber_heater)
+# - A chamber circulation fan (e.g., nevermore_fan)
+#
+# === PARAMETERS ===
+#   MATERIAL: Name of the filament material preset to apply
+#             Supported: PLA, ABS, PETG, ASA, PC, PA, PEEK, PEK, TPU, etc.
+#             Extended support for exotic blends like ESD-ABS, PVDF, MetalFill, Foam PLA
+#
+# === NOTES ===
+# - Each material includes chamber temp, fan speed, PA, and smoothing settings
+# - Some materials apply Z offset compensation or recommend special nozzle/hardware
+# - Certain blocks include warnings (e.g., "dry before use" or "use hardened nozzle")
+# - If you do not have a chamber heater, set `ACTIVE_CHAMBER_HEATING = False`
+# - You can expand this macro to include more materials as needed
+# - Unknown materials fall back to a safe PLA-like default
+#
+# === ADVANCED ===
+# This macro can be tied into slicer startup G-code or multi-material toolchanging macros.
+# You can also use it in combination with filament sensors or manual menu macros.
+
+gcode:
+    {% set CHAMBER_SENSOR = "temperature_sensor chamber_combined_mean" %}
+    {% set BED_HEATER = "heater_bed" %}
+    {% set BED_FAN = "nevermore_fan" %}
+    {% set ACTIVE_CHAMBER_HEATING = False %}  # Set to True if you have a dedicated chamber heater configured
+    {% set CHAMBER_HEATER = "chamber_heater" if ACTIVE_CHAMBER_HEATING else "" %}
+    {% set MATERIAL = params.MATERIAL|default("PLA")|string %}
+
+
+    SET_HEATER_TEMPERATURE HEATER={BED_HEATER} TARGET=0
+    SET_HEATER_TEMPERATURE HEATER=extruder TARGET=0
+
+
+    {% if MATERIAL in ['PLA', 'PLA-CF', 'PE', 'PE-CF'] %}
+        # PLA: Easy to print, low warping, no chamber needed. CF = carbon fiber, stiffer and more abrasive.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.035 | Chamber: 25°C" %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.035 SMOOTH=0.04
+
+    {% elif MATERIAL in ['PLA+', 'SILK-PLA'] %}
+        # PLA+: Stronger, tougher PLA. Silk PLA has glossy finish but may string more.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.038 | Chamber: 25°C" %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.038 SMOOTH=0.04
+
+    {% elif MATERIAL in ['PVDF', 'PVDF-CF', 'PVDF-GF'] %}
+        # PVDF: Chemical-resistant and strong. Requires high chamber temps and dry storage.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.055 | Chamber: 90°C | ⚠️ Moisture-sensitive. Dry before use." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET=90 SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.045
+
+    {% elif MATERIAL in ['ESD-PLA', 'ESD-ABS', 'ESD-PC', 'ESD-PEEK'] %}
+        # ESD-safe filaments for sensitive electronics. Can be brittle, dry before use.
+        {% set chamber_temp = 60 if 'PLA' in MATERIAL else 80 %}
+        {% set pa_val = 0.04 if 'PLA' in MATERIAL else 0.05 %}
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: " ~ pa_val|string ~ " | Chamber: " ~ chamber_temp|string ~ "°C | ⚠️ Dry before use for best performance." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={chamber_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA={pa_val} SMOOTH=0.045
+
+    {% elif MATERIAL == 'LW-PLA' %}
+        # LW-PLA: Lightweight PLA expands with heat. MUST reduce flow to ~65% manually.
+        {% set message = "Material: LW-PLA | PA: 0.03 | Chamber: 25°C | Reminder: Set flow to ~65%" %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.2
+        SET_PA PA=0.03 SMOOTH=0.04
+
+    {% elif MATERIAL == 'PLA-FOAM' %}
+        # PLA-FOAM: Similar to LW-PLA, foams up at extrusion temps. Lower flow ~60%.
+        {% set message = "Material: PLA-FOAM | PA: 0.03 | Chamber: 25°C | Reminder: Set flow to ~60%" %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
+        SET_PA PA=0.03 SMOOTH=0.04
+
+    {% elif MATERIAL in ['PETG', 'PETG-GF', 'PETG-CF', 'PET-CF'] %}
+        # PETG: Good strength/flexibility, more durable than PLA. May string. CF/GF are abrasive.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.03 | Chamber: 40°C" %}
+        RESPOND MSG="{message}"
+        M141 S40
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.03 SMOOTH=0.05
+        SET_GCODE_OFFSET Z=0.02  # PETG can be sticky; lift Z slightly to prevent nozzle drag
+
+    {% elif MATERIAL in ['ABS', 'ABS+', 'ABS-GF', 'ABS-CF'] %}
+        # ABS: Tough and heat-resistant, good for functional parts. Warps easily—requires enclosed chamber.
+        # CF (Carbon Fiber) / GF (Glass Fiber) versions are more rigid and very abrasive.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.05 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.05 SMOOTH=0.045
+
+    {% elif MATERIAL in ['ASA', 'ASA+', 'ASA-GF', 'ASA-CF', 'ASA-Aero'] %}
+        # ASA: UV-resistant alternative to ABS. Great for outdoor parts. Needs similar chamber temps to ABS.
+        # ASA-GF and ASA-CF are even more rigid and more abrasive.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.05 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.05 SMOOTH=0.045
+
+    {% elif MATERIAL == 'HIPS' %}
+        # HIPS: Used primarily as a dissolvable support for ABS. Requires similar chamber temps.
+        # ⚠️ Requires limonene bath for dissolution. Keep dry. May warp without chamber.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: HIPS | PA: 0.045 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Dissolves in limonene. Keep dry." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.045 SMOOTH=0.045
+
+    {% elif MATERIAL == 'BVOH' %}
+        # BVOH: Superior water-soluble support material. Less stringy than PVA but still moisture sensitive.
+        # ⚠️ Store in drybox. Dissolves faster in warm water. Do not overcool during print.
+        {% set message = "Material: BVOH | PA: 0.035 | Chamber: 25°C | ⚠️ Store dry. Dissolves in water." %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.2
+        SET_PA PA=0.035 SMOOTH=0.04
+
+    {% elif MATERIAL == 'PP' %}
+        # PP: Light and chemical-resistant. Warps easily and has poor adhesion. Needs chamber and special bed surface.
+        # ⚠️ Use PP-specific bed surface. Avoid cooling drafts. May require brim or raft.
+        {% set target_temp = 55 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PP | PA: 0.04 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Warps easily. PP bed surface recommended." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.04 SMOOTH=0.045
+
+    {% elif MATERIAL == 'PPSU' %}
+        # PPSU: High-performance thermoplastic. Chemical and heat-resistant. Needs very hot chamber and drying.
+        # ⚠️ Print with hardened nozzle. Needs chamber and high temps. Store dry.
+        {% set target_temp = 100 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PPSU | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Needs high temp & dry storage" %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'ULTEM' or MATERIAL == 'PEI' %}
+        # ULTEM / PEI: Extremely strong. High temp aerospace/engineering plastic. Needs chamber + hardened nozzle.
+        # ⚠️ Only for high-end printers. Dry thoroughly. Print hot.
+        {% set target_temp = 120 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: ULTEM/PEI | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Industrial use only. Dry & hot." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.06 SMOOTH=0.05
+    
+    {% elif MATERIAL == 'POLYMAX-PC' %}
+        # Polymaker PolyMax PC: Easier-to-print Polycarbonate blend. Good strength and clarity. Less prone to warping.
+        # ⚠️ Still requires chamber and hardened nozzle for long-term use.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PolyMax PC | PA: 0.05 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Tough and clear. Handle like PC." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.05 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'ULTRAFUSE-PAHT-CF15' %}
+        # BASF Ultrafuse PAHT CF15: High-temp nylon, 15% carbon fiber. Stiff, light, durable.
+        # ⚠️ Dry thoroughly. Use hardened nozzle. Requires chamber.
+        {% set target_temp = 70 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: Ultrafuse PAHT CF15 | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ High strength & very abrasive." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.06 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'PRUSAMENT-PETG-CF' %}
+        # Prusament PETG CF: Stiffer than normal PETG, reduced warping, excellent layer adhesion.
+        # ⚠️ Abrasive. Use hardened nozzle. Watch for brittle breakages if overcooled.
+        {% set message = "Material: Prusament PETG-CF | PA: 0.04 | Chamber: 45°C | ⚠️ Abrasive. Great dimensional stability." %}
+        RESPOND MSG="{message}"
+        M141 S45
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.4
+        SET_PA PA=0.04 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'PRUSAMENT-PLA-TOUGH' %}
+        # Prusament PLA Tough: Improved impact resistance vs. standard PLA. Still easy to print.
+        {% set message = "Material: Prusament PLA Tough | PA: 0.038 | Chamber: 25°C | Tougher than normal PLA." %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.038 SMOOTH=0.04
+    
+    {% elif MATERIAL in ['TPU-SOFT', 'TPU-85A'] %}
+        # TPU-Soft: Ultra-flexible variant. Requires extremely slow printing and short retractions.
+        # ⚠️ Direct drive required. Reduce speed to <20mm/s. Keep dry to avoid stringing.
+        {% set message = "Material: TPU-SOFT | PA: 0.055 | Chamber: 30°C | ⚠️ Print very slowly. Direct drive only." %}
+        RESPOND MSG="{message}"
+        M141 S30
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
+        SET_PA PA=0.055 SMOOTH=0.035
+        SET_GCODE_OFFSET Z=0.02
+    
+    {% elif MATERIAL == 'PA12-GF' %}
+        # PA12-GF: Glass-fiber filled Nylon 12. High strength, dimensional stability, very abrasive.
+        # ⚠️ Requires dry storage. Use hardened nozzle. Enclosure strongly recommended.
+        {% set target_temp = 70 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PA12-GF | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Dry thoroughly, very abrasive." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.06 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'BREAKAWAY' %}
+        # Breakaway: Rigid support material that peels away instead of dissolving. Great with ABS, ASA, PETG.
+        # ⚠️ Store dry. Avoid excessive cooling. Easy to print, good layer adhesion.
+        {% set message = "Material: Breakaway | PA: 0.035 | Chamber: 35°C | ⚠️ Peel-away support. Store dry." %}
+        RESPOND MSG="{message}"
+        M141 S35
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
+        SET_PA PA=0.035 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'NGEN' %}
+        # ColorFabb nGen: Easy-to-print PETG-like with smoother finish and less stringing. Based on Amphora AM3300.
+        {% set message = "Material: nGen | PA: 0.035 | Chamber: 30°C | Smoother than PETG, low stringing." %}
+        RESPOND MSG="{message}"
+        M141 S30
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.035 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'COLORFABB-HT' %}
+        # ColorFabb HT: High-temp, semi-crystalline Amphora-based copolyester. Tough and heat-resistant.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: ColorFabb HT | PA: 0.045 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | Tough and heat-tolerant. Dry before use." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.045 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'PPS' %}
+        # PPS: Exceptional chemical resistance, dimensional stability, and flame retardance. Used in automotive/aerospace.
+        {% set target_temp = 95 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PPS | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Industrial. Dry thoroughly. Print hot." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.06 SMOOTH=0.05
+    
+    {% elif MATERIAL in ['PVDF-BLEND', 'KYNAR', 'SOLEF'] %}
+        # PVDF Blend: Enhanced versions of PVDF for strength/flexibility. Used in semiconductors, chemical labs.
+        {% set target_temp = 85 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PVDF Blend | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Chemical resistant. Dry required." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'CARBONX-PC' %}
+        # CarbonX CFR-PC+: Carbon fiber-reinforced PC with excellent stiffness and heat performance.
+        # ⚠️ Use hardened nozzle. Dry before use. Requires enclosure.
+        {% set target_temp = 65 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: CarbonX PC+ | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ High stiffness, abrasive." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'ESUN-ABS+' %}
+        # eSun ABS+: Modified ABS with lower warping and easier layer adhesion. Still benefits from chamber heat.
+        {% set target_temp = 55 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: eSun ABS+ | PA: 0.045 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | Easier than regular ABS." %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.045 SMOOTH=0.045
+    
+    {% elif MATERIAL == 'RAISE3D-PLA+' %}
+        # Raise3D PLA+: Tougher PLA variant optimized for layer adhesion and strength.
+        {% set message = "Material: Raise3D PLA+ | PA: 0.038 | Chamber: 25°C | Tougher PLA with good printability." %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.038 SMOOTH=0.04
+
+    {% elif MATERIAL in ['PA', 'PA-GF', 'PA-CF', 'PAHT-CF', 'PA12-CF'] %}
+        # Nylon (PA): Strong, flexible, and wear-resistant. Extremely moisture-sensitive — dry before printing!
+        # CF = Carbon Fiber, GF = Glass Fiber, PAHT = high-temp nylon. Abrasive: use a hardened nozzle.
+        {% set target_temp = 65 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Dry thoroughly before use" %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.06 SMOOTH=0.045
+
+    {% elif MATERIAL in ['PC', 'PC-CF', 'PCTG'] %}
+        # PC (Polycarbonate): Very strong and heat resistant. Needs hot chamber. Tends to warp and absorb moisture.
+        # PC-CF is stiffer and more rigid. PCTG is a more forgiving blend.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.045
+
+    {% elif MATERIAL in ['PC-ABS', 'PCABS'] %}
+        # PC-ABS: Blend of PC and ABS. Easier to print than pure PC. Still wants a hot chamber and enclosure.
+        {% set target_temp = 70 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.045
+
+    {% elif MATERIAL == 'PEEK' %}
+        # PEEK: Ultra high-performance. Requires extremely hot chamber (110°C+). Dry thoroughly before use.
+        # Used in aerospace, medical, and industrial applications. Hardened nozzle & all-metal hotend required.
+        {% set target_temp = 110 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PEEK | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
+        RESPOND MSG="{message}"{% set message = "⏳ Waiting on heat | Chamber: " ~ chamber_waiting|string ~ " | Bed: " ~ bed_waiting|string %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.06 SMOOTH=0.05
+
+    {% elif MATERIAL == 'PEK' %}
+        # PEK: Slightly lower-temp cousin of PEEK. Still high performance and needs special hardware.
+        {% set target_temp = 90 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PEK | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.055 SMOOTH=0.05
+
+    {% elif MATERIAL == 'TPU' %}
+        # TPU: Flexible filament. Needs slow print speed. Watch for oozing. Can stretch during retraction.
+        # ⚠️ Tips: Print very slowly (15-30mm/s). Use direct drive. Avoid long Bowden tubes. Dry before use if soft or stringy.
+        {% set message = "Material: TPU | PA: 0.055 | Chamber: 35°C | ⚠️ Go slow, direct drive recommended" %}
+        RESPOND MSG="{message}"
+        M141 S35
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.055 SMOOTH=0.04
+        SET_GCODE_OFFSET Z=0.02
+
+    {% elif MATERIAL == 'TPE' %}
+        # TPE: Very soft rubber-like filament. Print slowly. Use direct drive extruder.
+        # ⚠️ Tips: Reduce retraction. Very flexible – print <25mm/s. May require increased nozzle temp. Dry before use.
+        {% set message = "Material: TPE | PA: 0.05 | Chamber: 30°C | ⚠️ Slow speed, direct drive only" %}
+        RESPOND MSG="{message}"
+        M141 S30
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.05 SMOOTH=0.04
+        SET_GCODE_OFFSET Z=0.02
+
+    {% elif MATERIAL in ['NINJAFLEX', 'NINJA-FLEX'] %}
+        # NinjaFlex: Ultra-flexible. Print extremely slow. Hard to control extrusion. Direct drive required.
+        # ⚠️ Tips: Dry well. No retraction if possible. Tight filament path. Print 10–20mm/s.
+        {% set message = "Material: Ninjaflex | PA: 0.045 | Chamber: 30°C | ⚠️ Print <20mm/s. No Bowden setups." %}
+        RESPOND MSG="{message}"
+        M141 S30
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
+        SET_PA PA=0.045 SMOOTH=0.035
+        SET_GCODE_OFFSET Z=0.02
+
+    {% elif MATERIAL in ['METALFILL', 'BRONZEFILL', 'COPPERFILL'] %}
+        # MetalFill: PLA blended with metal powder. Heavy, beautiful finish. Extremely abrasive—use hardened nozzle.
+        # ⚠️ Tips: Slower speed, hardened nozzle, check for settling in filament spool.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.04 | Chamber: 35°C | ⚠️ Abrasive – use hardened nozzle" %}
+        RESPOND MSG="{message}"
+        M141 S35
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.04 SMOOTH=0.045
+
+    {% elif MATERIAL in ['IRONFILL', 'MAGNETICFILL'] %}
+        # Magnetic/iron PLA: Similar to MetalFill but can rust. Very abrasive. Hardened steel nozzle recommended.
+        # ⚠️ Store dry to avoid rust. May interfere with inductive sensors.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.04 | Chamber: 35°C | ⚠️ Abrasive. Keep dry." %}
+        RESPOND MSG="{message}"
+        M141 S35
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.04 SMOOTH=0.045
+
+    {% elif MATERIAL in ['WOODFILL', 'CARBONFILL', 'KEVLARFILL'] %}
+        # Filled composites: Can clog if retracted too much. Lower print speeds. Use wider nozzle (0.6mm+) and hardened tip.
+        # ⚠️ Avoid retraction-heavy prints. Watch for clogs. WoodFill can scorch – keep nozzle temp moderate.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.045 | Chamber: 40°C | ⚠️ Composite: Use 0.6mm+ hardened nozzle" %}
+        RESPOND MSG="{message}"
+        M141 S40
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.045 SMOOTH=0.045
+
+    {% elif MATERIAL in ['MOLDLAY', 'CASTFIL', 'CASTING'] %}
+        # MoldLay: Used for casting. Can be melted out like wax. Brittle and needs low chamber temps.
+        # ⚠️ Avoid excessive cooling. Brittle at room temp. Supports should be minimal.
+        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.035 | Chamber: 25°C | ⚠️ Brittle – handle gently post-print" %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.035 SMOOTH=0.04
+
+    {% elif MATERIAL in ['PVA', 'SUPPORT-PVA'] %}
+        # PVA: Water-soluble support material. Store in airtight container. Extremely moisture-sensitive.
+        {% set message = "Material: PVA | PA: 0.035 | Chamber: 25°C | ⚠️ Water Soluble & Moisture Sensitive" %}
+        RESPOND MSG="{message}"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.0  # No fan to avoid drafts/drying out
+        SET_PA PA=0.035 SMOOTH=0.04
+
+    {% elif MATERIAL in ['PMMA', 'ACRYLIC'] %}
+        # PMMA: Transparent, acrylic-like. Shrinks a lot—needs chamber. Often cracks if too cold. Store dry.
+        {% set target_temp = 60 %}
+        {% set passive_wait = target_temp - 25 %}
+        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
+        {% set message = "Material: PMMA | PA: 0.04 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Brittle when moist, dry thoroughly" %}
+        RESPOND MSG="{message}"
+        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
+        SET_PA PA=0.04 SMOOTH=0.045
+
+    {% else %}
+        # Default fallback for unknown materials
+        RESPOND MSG="Material: Unknown | Default PA: 0.04 | Chamber: 25°C"
+        M141 S25
+        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
+        SET_PA PA=0.04 SMOOTH=0.045
+    {% endif %}
+
+[gcode_macro SET_PA]
+description: Set Pressure Advance with automatic nozzle and flow-based scaling
+variable_pa: 0.04
+
+# === OVERVIEW ===
+# Dynamically adjusts Pressure Advance (PA) based on:
+# - Configured nozzle size (from printer.cfg)
+# - Actual print flow vs max flow (defaults to 10/15 mm³/s)
+#
+# === HOW TO USE ===
+# SET_PA PA=<base_value> [FLOW=<actual_mm3/s>] [MAX_FLOW=<max_mm3/s>] [SMOOTH=<smoothing>]
+#
+# Example:
+#   SET_PA PA=0.05
+#   SET_PA PA=0.05 FLOW=35 MAX_FLOW=70
+#
+# === PARAMETERS ===
+#   PA        : Base PA for 100% flow (required)
+#   FLOW      : Actual flow rate in mm³/s (default: 10)
+#   MAX_FLOW  : Max hotend flow in mm³/s (default: 15)
+#   SMOOTH    : Optional smoothing (default: 0.045)
+
+gcode:
+    {% set base_pa   = params.PA|float %}
+    {% set smooth    = params.SMOOTH|default(0.045)|float %}
+    {% set nozzle    = printer.extruder.nozzle_diameter|float %}
+    {% set flow      = params.FLOW|default(30.0)|float %}
+    {% set max_flow  = params.MAX_FLOW|default(70.0)|float %}
+
+    # === Nozzle-based scaling ===
+    {% if nozzle <= 0.2 %}
+        {% set nozzle_scale = 1.8 %}
+    {% elif nozzle <= 0.3 %}
+        {% set nozzle_scale = 1.4 %}
+    {% elif nozzle <= 0.4 %}
+        {% set nozzle_scale = 1.0 %}
+    {% elif nozzle <= 0.6 %}
+        {% set nozzle_scale = 0.75 %}
+    {% elif nozzle <= 0.8 %}
+        {% set nozzle_scale = 0.5 %}
+    {% else %}
+        {% set nozzle_scale = 0.4 %}
+    {% endif %}
+
+    {% set scaled_pa = base_pa * nozzle_scale %}
+
+    # === Flow-based scaling (square root of flow ratio) ===
+    {% if max_flow > 0 %}
+        {% set flow_ratio = flow / max_flow %}
+        {% set flow_scale = flow_ratio ** 0.5 %}
+        {% set adjusted_pa = scaled_pa * flow_scale %}
+    {% else %}
+        {% set adjusted_pa = scaled_pa %}
+    {% endif %}
+
+    # === Set PA and store variable ===
+    SET_PRESSURE_ADVANCE ADVANCE={adjusted_pa} SMOOTH_TIME={smooth}
+    SET_GCODE_VARIABLE MACRO=SET_PA VARIABLE=pa VALUE={adjusted_pa}
+
+    # === Output status ===
+    {% set msg = "📐 PA scaled for nozzle " ~ nozzle|string ~ "mm | Base: " ~ base_pa|string ~
+                 " ➜ x" ~ nozzle_scale|string ~ " (nozzle) ➜ x" ~ flow_scale|string ~ " (flow) = " ~ adjusted_pa|string ~
+                 " | Smooth: " ~ smooth|string %}
+    RESPOND MSG="{msg}"
+
+
+[gcode_macro SET_CHAMBER_HEAT]
+description: Modular chamber heating logic with active/passive support, includes safety checks and debug output
+
+# === OVERVIEW ===
+# This macro heats the chamber to a target temperature using either:
+# 1. An active heater (like a dedicated chamber heater), or
+# 2. Passive heating (using the bed heater).
+# It controls the bed heater, an optional chamber heater, and a circulation fan.
+# It will block until the target temperature is reached.
+
+# === SAFETY WARNINGS ===
+# - Ensure your chamber temperature sensor is correctly installed and reporting.
+# - Watch your printer during the first few uses of this macro.
+# - Passive mode may take a long time to reach temperature.
+# - Don't overheat your enclosure — check max safe temps for your printer!
+
+# === PARAMETERS ===
+# TARGET      : (required) Target chamber temperature in °C.
+# SENSOR      : (optional) Temperature sensor name (default: temperature_sensor chamber_combined_mean).
+# HEATER      : (optional) Chamber heater name (used only if ACTIVE=True).
+# BED_HEATER  : (optional) Bed heater name (default: heater_bed).
+# FAN         : (optional) Circulation fan name (default: nevermore_fan).
+# ACTIVE      : (optional) If True, uses a dedicated heater; otherwise uses passive heating.
+
+# === USAGE ===
+# SET_CHAMBER_HEAT TARGET=60 ACTIVE=True HEATER="heater_generic chamber_heater"
+# SET_CHAMBER_HEAT TARGET=60 ACTIVE=False
+
+# === OVERVIEW ===
+# Heats the chamber using:
+# 🔥 Active: Chamber heater + bed + fan
+# ❄️ Passive: Bed heater only
+# ✅ Blocks until desired temperature is reached
+
+gcode:
+    # === 🎛️ Parse Parameters ===
+    {% set target = params.TARGET|int %}
+    {% set sensor = params.SENSOR|default('temperature_sensor chamber_combined_mean') %}
+    {% set heater = params.HEATER|default('') %}
+    {% set bed_heater = params.BED_HEATER|default('heater_bed') %}
+    {% set bed_fan = params.FAN|default('nevermore_fan') %}
+    {% set active = params.ACTIVE|default("false")|lower == 'true' %}
+    {% set wait_temp = target if active else target - 25 %}
+
+    {% set msg = "🧰 [CHAMBER HEAT] Init | Target: " ~ target ~ "°C | Wait until: " ~ wait_temp ~ "°C | Mode: " ~ ("🔥 Active" if active else "❄️ Passive") %}
+    RESPOND MSG="{msg}"
+
+    M141 S{target}  # Set virtual chamber temp for slicers
+
+    # === 🔥 ACTIVE MODE ===
+    {% if active %}
+        {% set msg = "🔥 [CHAMBER HEAT] Enabling active mode: chamber heater + bed + fan at full speed!" %}
+        RESPOND MSG="{msg}"
+
+        {% if heater|length > 0 %}
+            {% set msg = "🛠️ [CHAMBER HEAT] Chamber heater '" ~ heater ~ "' → " ~ target|string ~ "°C" %}
+            RESPOND MSG="{msg}"
+            SET_HEATER_TEMPERATURE HEATER={heater} TARGET={target}
+        {% endif %}
+
+        {% set msg = "🛏️ [CHAMBER HEAT] Bed heater '" ~ bed_heater ~ "' → " ~ target|string ~ "°C (support heat)" %}
+        RESPOND MSG="{msg}"
+        SET_HEATER_TEMPERATURE HEATER={bed_heater} TARGET={target}
+
+        {% set msg = "🌀 [CHAMBER HEAT] Fan '" ~ bed_fan ~ "' → speed = 100%" %}
+        RESPOND MSG="{msg}"
+        SET_FAN_SPEED FAN={bed_fan} SPEED=1.0
+
+    # === ❄️ PASSIVE MODE ===
+    {% else %}
+        {% if printer[sensor].temperature < wait_temp %}
+            {% set msg = "❄️ [CHAMBER HEAT] Chamber is cool (" ~ printer[sensor].temperature|round(1) ~ "°C) — warming with bed only!" %}
+            RESPOND MSG="{msg}"
+
+            {% set msg = "🌀 [CHAMBER HEAT] Fan '" ~ bed_fan ~ "' → speed = 50% (gentle circulation)" %}
+            RESPOND MSG="{msg}"
+            SET_FAN_SPEED FAN={bed_fan} SPEED=0.5
+
+            {% set msg = "🛏️ [CHAMBER HEAT] Bed heater '" ~ bed_heater ~ "' → 120°C (passive heating boost)" %}
+            RESPOND MSG="{msg}"
+            SET_HEATER_TEMPERATURE HEATER={bed_heater} TARGET=120
+
+            {% set msg = "⏳ [CHAMBER HEAT] Waiting for bed to reach 120°C..." %}
+            RESPOND MSG="{msg}"
+            TEMPERATURE_WAIT SENSOR="{bed_heater}" MINIMUM=120
+
+        {% else %}
+            {% set msg = "✅ [CHAMBER HEAT] Chamber already warm (" ~ printer[sensor].temperature|round(1) ~ "°C), skipping passive heat!" %}
+            RESPOND MSG="{msg}"
+        {% endif %}
+
+        {% set msg = "🌀 [CHAMBER HEAT] Fan '" ~ bed_fan ~ "' → speed = 100%" %}
+        RESPOND MSG="{msg}"
+        SET_FAN_SPEED FAN={bed_fan} SPEED=1.0
+    {% endif %}
+
+    # === ⏳ FINAL BLOCKING WAIT ===
+    {% set msg = "⏳ [CHAMBER HEAT] Waiting for chamber sensor '" ~ sensor ~ "' ≥ " ~ wait_temp ~ "°C..." %}
+    RESPOND MSG="{msg}"
+    TEMPERATURE_WAIT SENSOR="{sensor}" MINIMUM={wait_temp}
+
+    {% set msg = "🎉 [CHAMBER HEAT] Chamber ready! Final temp: " ~ printer[sensor].temperature|round(1) ~ "°C" %}
+    RESPOND MSG="{msg}"
+
+    
+[gcode_macro M106]
+rename_existing: G106
+description: Compresses fan speeds into 10–30% range if bed temp ≥ 70°C
+
+# === OVERVIEW ===
+# This macro overrides the default M106 behavior to apply a thermal-aware fan speed limiter.
+# When the bed temperature is at or above 70°C, it compresses the part cooling fan speed range
+# into a safer 10–30% range (i.e., 26–76 PWM) to reduce warping or delamination in high-temp materials.
+#
+# === WHY USE THIS ===
+# - Prevents excessive part cooling when printing materials like ABS, ASA, or PC.
+# - Helps maintain stable chamber temperatures and reduce thermal shock.
+# - Minimizes curling or layer splitting due to sudden cooling on hot beds.
+#
+# === HOW TO USE ===
+# Simply use M106 S<value> as usual in your G-code or slicer.
+# The macro will automatically adjust the fan speed if needed based on bed temperature.
+#
+# === NOTES ===
+# - This logic only applies when the bed temperature is 70°C or higher.
+# - Below 70°C, full-range fan control is allowed.
+# - You can customize the input/output compression range if needed.
+
+# === PARAMETERS ===
+#   S: Standard fan speed in 0–255 (required by M106)
+
+# Internal constants:
+#   min_input  = 26  (10% of 255)
+#   max_input  = 255 (100%)
+#   min_output = 26  (10%)
+#   max_output = 76  (30%)
+
+gcode:
+    {% set fan_speed = params.S|default(0)|int %}
+    {% set bed_temp = printer["heater_bed"].temperature %}
+    {% set min_input = 26 %}
+    {% set max_input = 255 %}
+    {% set min_output = 26 %}
+    {% set max_output = 76 %}
+
+    {% if bed_temp >= 70 %}
+        # If below threshold, limit fan to the lower compressed range (10–30%)
+        {% if fan_speed < min_input %}
+            {% set compressed_speed = min_output %}
+        {% else %}
+            {% set compressed_speed = (min_output + ((fan_speed - min_input) * (max_output - min_output) / (max_input - min_input)))|int %}
+        {% endif %}
+        G106 S{compressed_speed}
+    {% else %}
+        # Below threshold, allow full fan speed as requested
+        G106 S{fan_speed}
+    {% endif %}
+
@@ -0,0 +1,54 @@
+
+[thermistor Trianglelab-NTC100K-B3950]
+temperature1: 25
+resistance1: 103180
+temperature2: 150
+resistance2: 1366.2
+temperature3: 250
+resistance3: 168.6
+
+[temperature_sensor _chamber_1]
+sensor_type: Trianglelab-NTC100K-B3950
+sensor_pin: PF4
+min_temp: 0
+max_temp: 80
+gcode_id: CH1
+
+[temperature_sensor _chamber_2]
+sensor_type: Trianglelab-NTC100K-B3950
+sensor_pin: PF5
+min_temp: 0
+max_temp: 80
+gcode_id: CH2
+
+[temperature_sensor _chamber_3]
+sensor_type: Trianglelab-NTC100K-B3950
+sensor_pin: PF6
+min_temp: 0
+max_temp: 80
+gcode_id: CH3
+
+[temperature_sensor _chamber_4]
+sensor_type: Trianglelab-NTC100K-B3950
+sensor_pin: PF7
+min_temp: 0
+max_temp: 80
+gcode_id: CH4
+
+#[temperature_sensor chamber_combined_floor]
+#sensor_type: temperature_combined
+#sensor_list: temperature_sensor _chamber_1,temperature_sensor _chamber_2,temperature_sensor _chamber_3,temperature_sensor _chamber_4
+#combination_method: min
+#maximum_deviation: 999
+
+[temperature_sensor chamber_combined_mean]
+sensor_type: temperature_combined
+sensor_list: temperature_sensor _chamber_1,temperature_sensor _chamber_2,temperature_sensor _chamber_3,temperature_sensor _chamber_4
+combination_method: mean
+maximum_deviation: 999
+
+#[temperature_sensor chamber_combined_ceiling]
+#sensor_type: temperature_combined
+#sensor_list: temperature_sensor _chamber_1,temperature_sensor _chamber_2,temperature_sensor _chamber_3,temperature_sensor _chamber_4
+#combination_method: max
+#maximum_deviation: 999