From f5996881134c7addbf1a1cc061ee15bd08decc51 Mon Sep 17 00:00:00 2001 From: pi Date: Sat, 19 Apr 2025 14:51:21 +1000 Subject: [PATCH] printer.cfg modified - 19/04/25 - 14:51:18 --- printer_data/config/printer.cfg | 162 -------------------------------- 1 file changed, 162 deletions(-) diff --git a/printer_data/config/printer.cfg b/printer_data/config/printer.cfg index a6be913..7bed083 100644 --- a/printer_data/config/printer.cfg +++ b/printer_data/config/printer.cfg @@ -56,168 +56,6 @@ enable_force_move: True [gcode_arcs] resolution: 0.1 - -##################################################################### -# X/Y Stepper Settings -##################################################################### - -## X Stepper on MOTOR0(B Motor) -[stepper_x] -step_pin: PF13 -dir_pin: PF12 -enable_pin: !PF14 -rotation_distance: 40 -microsteps: 16 -full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper -endstop_pin: tmc2209_stepper_x:virtual_endstop -position_min: 0 -position_endstop: 352 -position_max: 352 - -##-------------------------------------------------------------------- -homing_speed: 50 #Max 100 -homing_retract_dist: 0 -homing_positive_dir: true - -## Make sure to update below for your relevant driver (2208 or 2209) -[tmc2209 stepper_x] -uart_pin: PC4 -interpolate: False -run_current: 0.9 -hold_current: 0.7 -sense_resistor: 0.110 -#stealthchop_threshold: 400 -diag_pin: ^PG6 -driver_SGTHRS: 60 #255 Most Sensitive 0 Least Sensitive - -## Y Stepper on MOTOR1 (A Motor) -[stepper_y] -step_pin: PG0 -dir_pin: PG1 -enable_pin: !PF15 -rotation_distance: 40 -microsteps: 16 -full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper -endstop_pin: tmc2209_stepper_y:virtual_endstop -position_min: 0 -position_endstop: 359 -position_max: 359 - -##-------------------------------------------------------------------- -homing_speed: 50 #Max 100 -homing_retract_dist: 0 -homing_positive_dir: true - -## Make sure to update below for your relevant driver (2208 or 2209) -[tmc2209 stepper_y] -uart_pin: PD11 -interpolate: False -run_current: 0.9 -hold_current: 0.7 -sense_resistor: 0.110 -#stealthchop_threshold: 400 -diag_pin: ^PG9 -driver_SGTHRS: 63 #255 Most Sensitive 0 Least Sensitive - -##################################################################### -# Z Stepper Settings -##################################################################### - -## Z0 Stepper - Front Left on MOTOR2_1 -[stepper_z] -step_pin: PF9 -dir_pin: PF10 -enable_pin: !PG2 -rotation_distance: 40 -gear_ratio: 80:16 -microsteps: 16 -#endstop_pin: probe:z_virtual_endstop -endstop_pin: EBB:gpio6 -## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) -## (+) value = endstop above Z0, (-) value = endstop below -## Increasing position_endstop brings nozzle closer to the bed -## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config -#position_endstop: -0.5 -##-------------------------------------------------------------------- - -## Uncomment below for 250mm build -#position_max: 240 - -## Uncomment below for 300mm build -#position_max: 290 - -## Uncomment below for 350mm build -position_max: 300 - -##-------------------------------------------------------------------- -position_min: -1 -homing_speed: 10 -second_homing_speed: 1 -homing_retract_dist: 2 - -## Make sure to update below for your relevant driver (2208 or 2209) -[tmc2209 stepper_z] -uart_pin: PF2 -interpolate: true -run_current: 0.8 -hold_current: 0.8 -sense_resistor: 0.110 -stealthchop_threshold: 0 - -## Z1 Stepper - Rear Left on MOTOR3 -[stepper_z1] -step_pin: PC13 -dir_pin: !PF0 -enable_pin: !PF1 -rotation_distance: 40 -gear_ratio: 80:16 -microsteps: 16 - -## Make sure to update below for your relevant driver (2208 or 2209) -[tmc2209 stepper_z1] -uart_pin: PE4 -interpolate: true -run_current: 0.8 -hold_current: 0.8 -sense_resistor: 0.110 -stealthchop_threshold: 0 - -## Z2 Stepper - Rear Right on MOTOR4 -[stepper_z2] -step_pin: PE2 -dir_pin: PE3 -enable_pin: !PD4 -rotation_distance: 40 -gear_ratio: 80:16 -microsteps: 16 - -## Make sure to update below for your relevant driver (2208 or 2209) -[tmc2209 stepper_z2] -uart_pin: PE1 -interpolate: true -run_current: 0.8 -hold_current: 0.80 -sense_resistor: 0.110 -stealthchop_threshold: 0 - -## Z3 Stepper - Front Right on MOTOR5 -[stepper_z3] -step_pin: PE6 -dir_pin: !PA14 -enable_pin: !PE0 -rotation_distance: 40 -gear_ratio: 80:16 -microsteps: 16 - -## Make sure to update below for your relevant driver (2208 or 2209) -[tmc2209 stepper_z3] -uart_pin: PD3 -interpolate: true -run_current: 0.8 -hold_current: 0.80 -sense_resistor: 0.110 -stealthchop_threshold: 0 - ##################################################################### # Bed Heater #####################################################################