[gcode_macro SET_MATERIAL]
description: Dynamically adjust chamber temps, fans, and behavior based on material

# === OVERVIEW ===
# This macro sets print parameters based on the selected filament type.
# It includes logic for fan control, pressure advance tuning, and chamber temperature management.
# Each material is uniquely handled with comments, proper defaults, and warnings where applicable.
#
# === WHY USE THIS ===
# - Ensures consistent print settings per material
# - Automatically adjusts temperature and environment conditions
# - Reduces manual tuning between material changes
# - Helps enforce safety (drying warnings, chamber heat warnings, etc.)
#
# === HOW TO USE ===
# Call the macro with:
#   SET_MATERIAL MATERIAL=<your_material>
#
# Example:
#   SET_MATERIAL MATERIAL=ABS
#
# === SETUP REQUIREMENTS ===
# You MUST configure:
# - A chamber temperature sensor (e.g., temperature_sensor chamber_combined_mean)
# - A bed heater (e.g., heater_bed)
# - Optionally, a chamber heater (e.g., heater_generic chamber_heater)
# - A chamber circulation fan (e.g., nevermore_fan)
#
# === PARAMETERS ===
#   MATERIAL: Name of the filament material preset to apply
#             Supported: PLA, ABS, PETG, ASA, PC, PA, PEEK, PEK, TPU, etc.
#             Extended support for exotic blends like ESD-ABS, PVDF, MetalFill, Foam PLA
#
# === NOTES ===
# - Each material includes chamber temp, fan speed, PA, and smoothing settings
# - Some materials apply Z offset compensation or recommend special nozzle/hardware
# - Certain blocks include warnings (e.g., "dry before use" or "use hardened nozzle")
# - If you do not have a chamber heater, set `ACTIVE_CHAMBER_HEATING = False`
# - You can expand this macro to include more materials as needed
# - Unknown materials fall back to a safe PLA-like default
#
# === ADVANCED ===
# This macro can be tied into slicer startup G-code or multi-material toolchanging macros.
# You can also use it in combination with filament sensors or manual menu macros.

gcode:
    {% set CHAMBER_SENSOR = "temperature_sensor chamber_combined_mean" %}
    {% set BED_HEATER = "heater_bed" %}
    {% set BED_FAN = "nevermore_fan" %}
    {% set ACTIVE_CHAMBER_HEATING = False %}  # Set to True if you have a dedicated chamber heater configured
    {% set CHAMBER_HEATER = "chamber_heater" if ACTIVE_CHAMBER_HEATING else "" %}
    {% set MATERIAL = params.MATERIAL|default("PLA")|string %}


    SET_HEATER_TEMPERATURE HEATER={BED_HEATER} TARGET=0
    SET_HEATER_TEMPERATURE HEATER=extruder TARGET=0


    {% if MATERIAL in ['PLA', 'PLA-CF', 'PE', 'PE-CF'] %}
        # PLA: Easy to print, low warping, no chamber needed. CF = carbon fiber, stiffer and more abrasive.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.035 | Chamber: 25°C" %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.035 SMOOTH=0.04

    {% elif MATERIAL in ['PLA+', 'SILK-PLA'] %}
        # PLA+: Stronger, tougher PLA. Silk PLA has glossy finish but may string more.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.038 | Chamber: 25°C" %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.038 SMOOTH=0.04

    {% elif MATERIAL in ['PVDF', 'PVDF-CF', 'PVDF-GF'] %}
        # PVDF: Chemical-resistant and strong. Requires high chamber temps and dry storage.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.055 | Chamber: 90°C | ⚠️ Moisture-sensitive. Dry before use." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET=90 SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.045

    {% elif MATERIAL in ['ESD-PLA', 'ESD-ABS', 'ESD-PC', 'ESD-PEEK'] %}
        # ESD-safe filaments for sensitive electronics. Can be brittle, dry before use.
        {% set chamber_temp = 60 if 'PLA' in MATERIAL else 80 %}
        {% set pa_val = 0.04 if 'PLA' in MATERIAL else 0.05 %}
        {% set message = "Material: " ~ MATERIAL ~ " | PA: " ~ pa_val|string ~ " | Chamber: " ~ chamber_temp|string ~ "°C | ⚠️ Dry before use for best performance." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={chamber_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA={pa_val} SMOOTH=0.045

    {% elif MATERIAL == 'LW-PLA' %}
        # LW-PLA: Lightweight PLA expands with heat. MUST reduce flow to ~65% manually.
        {% set message = "Material: LW-PLA | PA: 0.03 | Chamber: 25°C | Reminder: Set flow to ~65%" %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.2
        SET_PA PA=0.03 SMOOTH=0.04

    {% elif MATERIAL == 'PLA-FOAM' %}
        # PLA-FOAM: Similar to LW-PLA, foams up at extrusion temps. Lower flow ~60%.
        {% set message = "Material: PLA-FOAM | PA: 0.03 | Chamber: 25°C | Reminder: Set flow to ~60%" %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
        SET_PA PA=0.03 SMOOTH=0.04

    {% elif MATERIAL in ['PETG', 'PETG-GF', 'PETG-CF', 'PET-CF'] %}
        # PETG: Good strength/flexibility, more durable than PLA. May string. CF/GF are abrasive.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.03 | Chamber: 40°C" %}
        RESPOND MSG="{message}"
        M141 S40
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.03 SMOOTH=0.05
        SET_GCODE_OFFSET Z=0.02  # PETG can be sticky; lift Z slightly to prevent nozzle drag

    {% elif MATERIAL in ['ABS', 'ABS+', 'ABS-GF', 'ABS-CF'] %}
        # ABS: Tough and heat-resistant, good for functional parts. Warps easily—requires enclosed chamber.
        # CF (Carbon Fiber) / GF (Glass Fiber) versions are more rigid and very abrasive.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.05 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.05 SMOOTH=0.045

    {% elif MATERIAL in ['ASA', 'ASA+', 'ASA-GF', 'ASA-CF', 'ASA-Aero'] %}
        # ASA: UV-resistant alternative to ABS. Great for outdoor parts. Needs similar chamber temps to ABS.
        # ASA-GF and ASA-CF are even more rigid and more abrasive.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.05 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.05 SMOOTH=0.045

    {% elif MATERIAL == 'HIPS' %}
        # HIPS: Used primarily as a dissolvable support for ABS. Requires similar chamber temps.
        # ⚠️ Requires limonene bath for dissolution. Keep dry. May warp without chamber.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: HIPS | PA: 0.045 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Dissolves in limonene. Keep dry." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.045 SMOOTH=0.045

    {% elif MATERIAL == 'BVOH' %}
        # BVOH: Superior water-soluble support material. Less stringy than PVA but still moisture sensitive.
        # ⚠️ Store in drybox. Dissolves faster in warm water. Do not overcool during print.
        {% set message = "Material: BVOH | PA: 0.035 | Chamber: 25°C | ⚠️ Store dry. Dissolves in water." %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.2
        SET_PA PA=0.035 SMOOTH=0.04

    {% elif MATERIAL == 'PP' %}
        # PP: Light and chemical-resistant. Warps easily and has poor adhesion. Needs chamber and special bed surface.
        # ⚠️ Use PP-specific bed surface. Avoid cooling drafts. May require brim or raft.
        {% set target_temp = 55 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PP | PA: 0.04 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Warps easily. PP bed surface recommended." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.04 SMOOTH=0.045

    {% elif MATERIAL == 'PPSU' %}
        # PPSU: High-performance thermoplastic. Chemical and heat-resistant. Needs very hot chamber and drying.
        # ⚠️ Print with hardened nozzle. Needs chamber and high temps. Store dry.
        {% set target_temp = 100 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PPSU | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Needs high temp & dry storage" %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.045
    
    {% elif MATERIAL == 'ULTEM' or MATERIAL == 'PEI' %}
        # ULTEM / PEI: Extremely strong. High temp aerospace/engineering plastic. Needs chamber + hardened nozzle.
        # ⚠️ Only for high-end printers. Dry thoroughly. Print hot.
        {% set target_temp = 120 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: ULTEM/PEI | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Industrial use only. Dry & hot." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.06 SMOOTH=0.05
    
    {% elif MATERIAL == 'POLYMAX-PC' %}
        # Polymaker PolyMax PC: Easier-to-print Polycarbonate blend. Good strength and clarity. Less prone to warping.
        # ⚠️ Still requires chamber and hardened nozzle for long-term use.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PolyMax PC | PA: 0.05 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Tough and clear. Handle like PC." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.05 SMOOTH=0.045
    
    {% elif MATERIAL == 'ULTRAFUSE-PAHT-CF15' %}
        # BASF Ultrafuse PAHT CF15: High-temp nylon, 15% carbon fiber. Stiff, light, durable.
        # ⚠️ Dry thoroughly. Use hardened nozzle. Requires chamber.
        {% set target_temp = 70 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: Ultrafuse PAHT CF15 | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ High strength & very abrasive." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.06 SMOOTH=0.045
    
    {% elif MATERIAL == 'PRUSAMENT-PETG-CF' %}
        # Prusament PETG CF: Stiffer than normal PETG, reduced warping, excellent layer adhesion.
        # ⚠️ Abrasive. Use hardened nozzle. Watch for brittle breakages if overcooled.
        {% set message = "Material: Prusament PETG-CF | PA: 0.04 | Chamber: 45°C | ⚠️ Abrasive. Great dimensional stability." %}
        RESPOND MSG="{message}"
        M141 S45
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.4
        SET_PA PA=0.04 SMOOTH=0.045
    
    {% elif MATERIAL == 'PRUSAMENT-PLA-TOUGH' %}
        # Prusament PLA Tough: Improved impact resistance vs. standard PLA. Still easy to print.
        {% set message = "Material: Prusament PLA Tough | PA: 0.038 | Chamber: 25°C | Tougher than normal PLA." %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.038 SMOOTH=0.04
    
    {% elif MATERIAL in ['TPU-SOFT', 'TPU-85A'] %}
        # TPU-Soft: Ultra-flexible variant. Requires extremely slow printing and short retractions.
        # ⚠️ Direct drive required. Reduce speed to <20mm/s. Keep dry to avoid stringing.
        {% set message = "Material: TPU-SOFT | PA: 0.055 | Chamber: 30°C | ⚠️ Print very slowly. Direct drive only." %}
        RESPOND MSG="{message}"
        M141 S30
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
        SET_PA PA=0.055 SMOOTH=0.035
        SET_GCODE_OFFSET Z=0.02
    
    {% elif MATERIAL == 'PA12-GF' %}
        # PA12-GF: Glass-fiber filled Nylon 12. High strength, dimensional stability, very abrasive.
        # ⚠️ Requires dry storage. Use hardened nozzle. Enclosure strongly recommended.
        {% set target_temp = 70 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PA12-GF | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Dry thoroughly, very abrasive." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.06 SMOOTH=0.045
    
    {% elif MATERIAL == 'BREAKAWAY' %}
        # Breakaway: Rigid support material that peels away instead of dissolving. Great with ABS, ASA, PETG.
        # ⚠️ Store dry. Avoid excessive cooling. Easy to print, good layer adhesion.
        {% set message = "Material: Breakaway | PA: 0.035 | Chamber: 35°C | ⚠️ Peel-away support. Store dry." %}
        RESPOND MSG="{message}"
        M141 S35
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
        SET_PA PA=0.035 SMOOTH=0.045
    
    {% elif MATERIAL == 'NGEN' %}
        # ColorFabb nGen: Easy-to-print PETG-like with smoother finish and less stringing. Based on Amphora AM3300.
        {% set message = "Material: nGen | PA: 0.035 | Chamber: 30°C | Smoother than PETG, low stringing." %}
        RESPOND MSG="{message}"
        M141 S30
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.035 SMOOTH=0.045
    
    {% elif MATERIAL == 'COLORFABB-HT' %}
        # ColorFabb HT: High-temp, semi-crystalline Amphora-based copolyester. Tough and heat-resistant.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: ColorFabb HT | PA: 0.045 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | Tough and heat-tolerant. Dry before use." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.045 SMOOTH=0.045
    
    {% elif MATERIAL == 'PPS' %}
        # PPS: Exceptional chemical resistance, dimensional stability, and flame retardance. Used in automotive/aerospace.
        {% set target_temp = 95 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PPS | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Industrial. Dry thoroughly. Print hot." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.06 SMOOTH=0.05
    
    {% elif MATERIAL in ['PVDF-BLEND', 'KYNAR', 'SOLEF'] %}
        # PVDF Blend: Enhanced versions of PVDF for strength/flexibility. Used in semiconductors, chemical labs.
        {% set target_temp = 85 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PVDF Blend | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Chemical resistant. Dry required." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.045
    
    {% elif MATERIAL == 'CARBONX-PC' %}
        # CarbonX CFR-PC+: Carbon fiber-reinforced PC with excellent stiffness and heat performance.
        # ⚠️ Use hardened nozzle. Dry before use. Requires enclosure.
        {% set target_temp = 65 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: CarbonX PC+ | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ High stiffness, abrasive." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.045
    
    {% elif MATERIAL == 'ESUN-ABS+' %}
        # eSun ABS+: Modified ABS with lower warping and easier layer adhesion. Still benefits from chamber heat.
        {% set target_temp = 55 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: eSun ABS+ | PA: 0.045 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | Easier than regular ABS." %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.045 SMOOTH=0.045
    
    {% elif MATERIAL == 'RAISE3D-PLA+' %}
        # Raise3D PLA+: Tougher PLA variant optimized for layer adhesion and strength.
        {% set message = "Material: Raise3D PLA+ | PA: 0.038 | Chamber: 25°C | Tougher PLA with good printability." %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.038 SMOOTH=0.04

    {% elif MATERIAL in ['PA', 'PA-GF', 'PA-CF', 'PAHT-CF', 'PA12-CF'] %}
        # Nylon (PA): Strong, flexible, and wear-resistant. Extremely moisture-sensitive — dry before printing!
        # CF = Carbon Fiber, GF = Glass Fiber, PAHT = high-temp nylon. Abrasive: use a hardened nozzle.
        {% set target_temp = 65 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Dry thoroughly before use" %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.06 SMOOTH=0.045

    {% elif MATERIAL in ['PC', 'PC-CF', 'PCTG'] %}
        # PC (Polycarbonate): Very strong and heat resistant. Needs hot chamber. Tends to warp and absorb moisture.
        # PC-CF is stiffer and more rigid. PCTG is a more forgiving blend.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.045

    {% elif MATERIAL in ['PC-ABS', 'PCABS'] %}
        # PC-ABS: Blend of PC and ABS. Easier to print than pure PC. Still wants a hot chamber and enclosure.
        {% set target_temp = 70 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.045

    {% elif MATERIAL == 'PEEK' %}
        # PEEK: Ultra high-performance. Requires extremely hot chamber (110°C+). Dry thoroughly before use.
        # Used in aerospace, medical, and industrial applications. Hardened nozzle & all-metal hotend required.
        {% set target_temp = 110 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PEEK | PA: 0.06 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
        RESPOND MSG="{message}"{% set message = "⏳ Waiting on heat | Chamber: " ~ chamber_waiting|string ~ " | Bed: " ~ bed_waiting|string %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.06 SMOOTH=0.05

    {% elif MATERIAL == 'PEK' %}
        # PEK: Slightly lower-temp cousin of PEEK. Still high performance and needs special hardware.
        {% set target_temp = 90 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PEK | PA: 0.055 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.055 SMOOTH=0.05

    {% elif MATERIAL == 'TPU' %}
        # TPU: Flexible filament. Needs slow print speed. Watch for oozing. Can stretch during retraction.
        # ⚠️ Tips: Print very slowly (15-30mm/s). Use direct drive. Avoid long Bowden tubes. Dry before use if soft or stringy.
        {% set message = "Material: TPU | PA: 0.055 | Chamber: 35°C | ⚠️ Go slow, direct drive recommended" %}
        RESPOND MSG="{message}"
        M141 S35
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.055 SMOOTH=0.04
        SET_GCODE_OFFSET Z=0.02

    {% elif MATERIAL == 'TPE' %}
        # TPE: Very soft rubber-like filament. Print slowly. Use direct drive extruder.
        # ⚠️ Tips: Reduce retraction. Very flexible – print <25mm/s. May require increased nozzle temp. Dry before use.
        {% set message = "Material: TPE | PA: 0.05 | Chamber: 30°C | ⚠️ Slow speed, direct drive only" %}
        RESPOND MSG="{message}"
        M141 S30
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.05 SMOOTH=0.04
        SET_GCODE_OFFSET Z=0.02

    {% elif MATERIAL in ['NINJAFLEX', 'NINJA-FLEX'] %}
        # NinjaFlex: Ultra-flexible. Print extremely slow. Hard to control extrusion. Direct drive required.
        # ⚠️ Tips: Dry well. No retraction if possible. Tight filament path. Print 10–20mm/s.
        {% set message = "Material: Ninjaflex | PA: 0.045 | Chamber: 30°C | ⚠️ Print <20mm/s. No Bowden setups." %}
        RESPOND MSG="{message}"
        M141 S30
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.3
        SET_PA PA=0.045 SMOOTH=0.035
        SET_GCODE_OFFSET Z=0.02

    {% elif MATERIAL in ['METALFILL', 'BRONZEFILL', 'COPPERFILL'] %}
        # MetalFill: PLA blended with metal powder. Heavy, beautiful finish. Extremely abrasive—use hardened nozzle.
        # ⚠️ Tips: Slower speed, hardened nozzle, check for settling in filament spool.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.04 | Chamber: 35°C | ⚠️ Abrasive – use hardened nozzle" %}
        RESPOND MSG="{message}"
        M141 S35
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.04 SMOOTH=0.045

    {% elif MATERIAL in ['IRONFILL', 'MAGNETICFILL'] %}
        # Magnetic/iron PLA: Similar to MetalFill but can rust. Very abrasive. Hardened steel nozzle recommended.
        # ⚠️ Store dry to avoid rust. May interfere with inductive sensors.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.04 | Chamber: 35°C | ⚠️ Abrasive. Keep dry." %}
        RESPOND MSG="{message}"
        M141 S35
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.04 SMOOTH=0.045

    {% elif MATERIAL in ['WOODFILL', 'CARBONFILL', 'KEVLARFILL'] %}
        # Filled composites: Can clog if retracted too much. Lower print speeds. Use wider nozzle (0.6mm+) and hardened tip.
        # ⚠️ Avoid retraction-heavy prints. Watch for clogs. WoodFill can scorch – keep nozzle temp moderate.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.045 | Chamber: 40°C | ⚠️ Composite: Use 0.6mm+ hardened nozzle" %}
        RESPOND MSG="{message}"
        M141 S40
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.045 SMOOTH=0.045

    {% elif MATERIAL in ['MOLDLAY', 'CASTFIL', 'CASTING'] %}
        # MoldLay: Used for casting. Can be melted out like wax. Brittle and needs low chamber temps.
        # ⚠️ Avoid excessive cooling. Brittle at room temp. Supports should be minimal.
        {% set message = "Material: " ~ MATERIAL ~ " | PA: 0.035 | Chamber: 25°C | ⚠️ Brittle – handle gently post-print" %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.035 SMOOTH=0.04

    {% elif MATERIAL in ['PVA', 'SUPPORT-PVA'] %}
        # PVA: Water-soluble support material. Store in airtight container. Extremely moisture-sensitive.
        {% set message = "Material: PVA | PA: 0.035 | Chamber: 25°C | ⚠️ Water Soluble & Moisture Sensitive" %}
        RESPOND MSG="{message}"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.0  # No fan to avoid drafts/drying out
        SET_PA PA=0.035 SMOOTH=0.04

    {% elif MATERIAL in ['PMMA', 'ACRYLIC'] %}
        # PMMA: Transparent, acrylic-like. Shrinks a lot—needs chamber. Often cracks if too cold. Store dry.
        {% set target_temp = 60 %}
        {% set passive_wait = target_temp - 25 %}
        {% set CHAMBER_LABEL = "(active heater)" if ACTIVE_CHAMBER_HEATING else "(passive via bed, will start at ≥" ~ passive_wait|string ~ "°C)" %}
        {% set message = "Material: PMMA | PA: 0.04 | Chamber: " ~ target_temp|string ~ "°C " ~ CHAMBER_LABEL ~ " | ⚠️ Brittle when moist, dry thoroughly" %}
        RESPOND MSG="{message}"
        SET_CHAMBER_HEAT TARGET={target_temp} SENSOR="{CHAMBER_SENSOR}" HEATER={CHAMBER_HEATER} BED_HEATER={BED_HEATER} FAN={BED_FAN} ACTIVE={ACTIVE_CHAMBER_HEATING}
        SET_PA PA=0.04 SMOOTH=0.045

    {% else %}
        # Default fallback for unknown materials
        RESPOND MSG="Material: Unknown | Default PA: 0.04 | Chamber: 25°C"
        M141 S25
        SET_FAN_SPEED FAN={BED_FAN} SPEED=0.5
        SET_PA PA=0.04 SMOOTH=0.045
    {% endif %}