78 lines
1.7 KiB
INI
78 lines
1.7 KiB
INI
# This file contains common pin mappings for the BIGTREETECH EBB USB board.
|
|
# To use this config, the firmware should be compiled for the RP2040 with "USB".
|
|
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu EBB]
|
|
serial: /dev/serial/by-id/usb-Klipper_rp2040_5044340310A5581C-if00
|
|
|
|
[temperature_sensor EBB_NTC]
|
|
sensor_type: Generic 3950
|
|
sensor_pin: EBB:gpio27
|
|
|
|
[lis2dw]
|
|
cs_pin: EBB:gpio1
|
|
spi_bus: spi0a
|
|
axes_map: z,x,y
|
|
|
|
[resonance_tester]
|
|
probe_points: 175, 175, 20
|
|
accel_chip: lis2dw
|
|
|
|
[extruder]
|
|
step_pin: EBB:gpio18
|
|
dir_pin: !EBB:gpio19
|
|
enable_pin: !EBB:gpio17
|
|
gear_ratio: 50:10
|
|
microsteps: 16
|
|
rotation_distance: 22.6789511
|
|
full_steps_per_rotation: 200
|
|
nozzle_diameter: 0.600
|
|
filament_diameter: 1.750
|
|
heater_pin: EBB:gpio7
|
|
pullup_resistor: 2200 # 2.2K
|
|
sensor_type: PT1000
|
|
sensor_pin: EBB:gpio26
|
|
max_extrude_cross_section: 5
|
|
min_temp: 0
|
|
max_temp: 350
|
|
|
|
#sensor_type: MAX31865
|
|
#sensor_pin: EBB:gpio9
|
|
#spi_bus: spi1a
|
|
#rtd_nominal_r: 1000
|
|
#rtd_reference_r: 4300
|
|
#rtd_num_of_wires: 2
|
|
#rtd_use_50Hz_filter: True
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: EBB:gpio20
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
#[fan] # fan1
|
|
#pin: EBB:gpio14
|
|
|
|
[heater_fan hotend_fan] # fan2
|
|
pin: EBB:gpio14
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
|
|
#[fan_generic fan3]
|
|
#pin: EBB:gpio5
|
|
|
|
#[fan_generic 4W_FAN]
|
|
#pin: EBB:gpio16
|
|
#tachometer_pin: EBB:gpio12
|
|
#tachometer_ppr: 1
|
|
|
|
[filament_switch_sensor toolhead_switch_sensor]
|
|
switch_pin: EBB:gpio13
|
|
pause_on_runout: True
|
|
runout_gcode:
|
|
PAUSE # [pause_resume] is required in printer.cfg
|
|
M117 Toolhead Filament switch runout
|
|
insert_gcode:
|
|
M117 Toolhead Filament switch inserted
|