160 lines
3.9 KiB
INI
160 lines
3.9 KiB
INI
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## X Stepper on MOTOR0(B Motor)
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_min: 0
|
|
position_endstop: 352
|
|
position_max: 352
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: False
|
|
run_current: 0.9
|
|
hold_current: 0.7
|
|
sense_resistor: 0.110
|
|
#stealthchop_threshold: 400
|
|
diag_pin: ^PG6
|
|
driver_SGTHRS: 60 #255 Most Sensitive 0 Least Sensitive
|
|
|
|
## Y Stepper on MOTOR1 (A Motor)
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_min: 0
|
|
position_endstop: 359
|
|
position_max: 359
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: False
|
|
run_current: 0.9
|
|
hold_current: 0.7
|
|
sense_resistor: 0.110
|
|
#stealthchop_threshold: 400
|
|
diag_pin: ^PG9
|
|
driver_SGTHRS: 63 #255 Most Sensitive 0 Least Sensitive
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left on MOTOR2_1
|
|
[stepper_z]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
#endstop_pin: probe:z_virtual_endstop
|
|
endstop_pin: EBB:gpio6
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: -0.5
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_max: 240
|
|
|
|
## Uncomment below for 300mm build
|
|
#position_max: 290
|
|
|
|
## Uncomment below for 350mm build
|
|
position_max: 300
|
|
|
|
##--------------------------------------------------------------------
|
|
position_min: -1
|
|
homing_speed: 10
|
|
second_homing_speed: 1
|
|
homing_retract_dist: 2
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PF2
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z1 Stepper - Rear Left on MOTOR3
|
|
[stepper_z1]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PE4
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z2 Stepper - Rear Right on MOTOR4
|
|
[stepper_z2]
|
|
step_pin: PE2
|
|
dir_pin: PE3
|
|
enable_pin: !PD4
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PE1
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.80
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z3 Stepper - Front Right on MOTOR5
|
|
[stepper_z3]
|
|
step_pin: PE6
|
|
dir_pin: !PA14
|
|
enable_pin: !PE0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PD3
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.80
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0 |