560 lines
15 KiB
INI
560 lines
15 KiB
INI
# This file contains common pin mappings for the BigTreeTech OctoPus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[include ./TOOLHEAD/*.cfg]
|
|
[include ./SYSTEM/*.cfg]
|
|
[include ./CUSTOM/*.cfg]
|
|
|
|
[mcu]
|
|
## [X in MOTOR0] - B Motor
|
|
## [Y in MOTOR1] - A Motor
|
|
## [E in MOTOR6] - Extruder
|
|
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_360026001950534146373920-if00
|
|
restart_method: command
|
|
##--------------------------------------------------------------------
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 500
|
|
max_accel: 4200 #Max 4000
|
|
#max_y_accel: 4200
|
|
#max_x_accel: 8000
|
|
#max_accel: 10000 #Testing - revert back to above line after!
|
|
#max_accel_to_decel: 10000 #Testing - revert back to above line after!
|
|
max_z_velocity: 30 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 500
|
|
square_corner_velocity: 2.0
|
|
minimum_cruise_ratio: 0
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
[skew_correction]
|
|
[exclude_object]
|
|
[firmware_retraction]
|
|
[gcode_arcs]
|
|
resolution: 0.1
|
|
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## X Stepper on MOTOR0(B Motor)
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_min: 0
|
|
position_endstop: 352
|
|
position_max: 352
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: False
|
|
run_current: 0.9
|
|
hold_current: 0.7
|
|
sense_resistor: 0.110
|
|
#stealthchop_threshold: 400
|
|
diag_pin: ^PG6
|
|
driver_SGTHRS: 60 #255 Most Sensitive 0 Least Sensitive
|
|
|
|
## Y Stepper on MOTOR1 (A Motor)
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_min: 0
|
|
position_endstop: 359
|
|
position_max: 359
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 50 #Max 100
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: False
|
|
run_current: 0.9
|
|
hold_current: 0.7
|
|
sense_resistor: 0.110
|
|
#stealthchop_threshold: 400
|
|
diag_pin: ^PG9
|
|
driver_SGTHRS: 63 #255 Most Sensitive 0 Least Sensitive
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left on MOTOR2_1
|
|
[stepper_z]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
#endstop_pin: probe:z_virtual_endstop
|
|
endstop_pin: EBB:gpio6
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: -0.5
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_max: 240
|
|
|
|
## Uncomment below for 300mm build
|
|
#position_max: 290
|
|
|
|
## Uncomment below for 350mm build
|
|
position_max: 300
|
|
|
|
##--------------------------------------------------------------------
|
|
position_min: -1
|
|
homing_speed: 10
|
|
second_homing_speed: 1
|
|
homing_retract_dist: 2
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PF2
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z1 Stepper - Rear Left on MOTOR3
|
|
[stepper_z1]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PE4
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z2 Stepper - Rear Right on MOTOR4
|
|
[stepper_z2]
|
|
step_pin: PE2
|
|
dir_pin: PE3
|
|
enable_pin: !PD4
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PE1
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.80
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z3 Stepper - Front Right on MOTOR5
|
|
[stepper_z3]
|
|
step_pin: PE6
|
|
dir_pin: !PA14
|
|
enable_pin: !PE0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PD3
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.80
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
## SSR Pin - BED_OUT
|
|
heater_pin: PA1
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed
|
|
max_power: 1.0
|
|
min_temp: 0
|
|
max_temp: 125
|
|
#control: pid
|
|
#pid_kp: 58.437
|
|
#pid_ki: 2.347
|
|
#pid_kd: 363.769
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[fan]
|
|
## Part Cooling Fan - CPAP 7040
|
|
pin: PG15
|
|
max_power: 1.0
|
|
kick_start_time: 0.05
|
|
hardware_pwm: False
|
|
cycle_time: 0.005
|
|
off_below: 0.1
|
|
|
|
|
|
[controller_fan stepper_fan]
|
|
## Controller fan - CNC_FAN2
|
|
pin: PD12
|
|
max_power: 0.9
|
|
kick_start_time: 0.5
|
|
fan_speed: 0.7
|
|
|
|
[controller_fan electronic_chamber_fans]
|
|
## Controller fan - CNC_FAN2
|
|
pin: PD13
|
|
max_power: 0.8
|
|
kick_start_time: 0.5
|
|
fan_speed: 0.4
|
|
|
|
|
|
[temperature_fan exhaust_fan]
|
|
pin: PE5
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
cycle_time: 0.05
|
|
hardware_pwm: True
|
|
off_below: 0.15
|
|
|
|
sensor_type: temperature_combined
|
|
sensor_list: temperature_sensor _chamber_1, temperature_sensor _chamber_2, temperature_sensor _chamber_3, temperature_sensor _chamber_4
|
|
combination_method: mean
|
|
maximum_deviation: 999
|
|
|
|
control: pid
|
|
pid_Kp: 35.0
|
|
pid_Ki: 12
|
|
pid_Kd: 4.0
|
|
pid_deriv_time: 2.0
|
|
|
|
target_temp: 50.0
|
|
min_temp: 0
|
|
max_temp: 110
|
|
min_speed: 0.149
|
|
max_speed: 1.0
|
|
|
|
gcode_id: C
|
|
|
|
#[temperature_fan exhaust_fan]
|
|
## Exhaust fan - CNC_FAN3
|
|
#pin: PE5
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#cycle_time:0.05
|
|
#off_below:0.1
|
|
#sensor_type: temperature_combined
|
|
#sensor_list: temperature_sensor _chamber_1,temperature_sensor _chamber_2,temperature_sensor _chamber_3,temperature_sensor _chamber_4
|
|
#combination_method: mean
|
|
#maximum_deviation: 999
|
|
#min_temp: 0
|
|
#max_temp: 80
|
|
#target_temp: 35.0
|
|
#max_delta: 0.5
|
|
#max_speed: 1.0
|
|
#min_speed: 0.3
|
|
#control: watermark
|
|
#gcode_id: C
|
|
|
|
[gcode_macro M141]
|
|
gcode:
|
|
{% set s = params.S|default(0)|float %}
|
|
SET_TEMPERATURE_FAN_TARGET temperature_fan="exhaust_fan" target={s}
|
|
|
|
[fan_generic nevermore_fan]
|
|
pin: PD15
|
|
max_power: 1.0
|
|
kick_start_time: 1.0
|
|
cycle_time: 0.05
|
|
off_below: 0.13
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
#[output_pin caselight]
|
|
# Chamber Lighting - HE1 Connector (Optional)
|
|
#pin: PB11
|
|
#pwm:true
|
|
#shutdown_value: 0
|
|
#value:1
|
|
#cycle_time: 0.01
|
|
|
|
[output_pin daylight]
|
|
pin: PB11
|
|
pwm: True
|
|
cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
#[safe_z_home]
|
|
## XY Location of the Z Endstop Switch
|
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
|
## (such as 157,305) after going through Z Endstop Pin
|
|
## Location Definition step.
|
|
#home_xy_position:175,175
|
|
#speed:100
|
|
#z_hop:10
|
|
|
|
[quad_gantry_level]
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
|
|
#--------------------------------------------------------------------
|
|
## Gantry Corners for 250mm Build
|
|
## Uncomment for 250mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 310, 320
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,175
|
|
# 200,175
|
|
# 200,25
|
|
|
|
## Gantry Corners for 300mm Build
|
|
## Uncomment for 300mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 360,370
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,225
|
|
# 250,225
|
|
# 250,25
|
|
|
|
## Gantry Corners for 350mm Build
|
|
## Uncomment for 350mm build
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
#--------------------------------------------------------------------
|
|
speed: 200
|
|
horizontal_move_z: 2
|
|
retries: 15
|
|
retry_tolerance: 0.015
|
|
max_adjust: 5
|
|
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[neopixel front_logo]
|
|
|
|
pin: PB0
|
|
# The pin connected to the neopixel. This parameter must be
|
|
# provided.
|
|
chain_count: 7
|
|
# The number of Neopixel chips that are "daisy chained" to the
|
|
# provided pin. The default is 1 (which indicates only a single
|
|
# Neopixel is connected to the pin).
|
|
color_order: GRB
|
|
# Set the pixel order required by the LED hardware (using a string
|
|
# containing the letters R, G, B, W with W optional). Alternatively,
|
|
# this may be a comma separated list of pixel orders - one for each
|
|
# LED in the chain. The default is GRB.
|
|
initial_RED: 1.0
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 0.0
|
|
initial_WHITE: 0.0
|
|
# See the "led" section for information on these parameters.
|
|
#--------------------------------------------------------------------
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
|
|
[gcode_macro G32]
|
|
description: Home XYZ mesh calibrate
|
|
gcode:
|
|
STATUS_HOMING
|
|
BED_MESH_CLEAR
|
|
G28
|
|
QUAD_GANTRY_LEVEL
|
|
STATUS_MESHING
|
|
BED_MESH_CALIBRATE
|
|
G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } Z30 F4500
|
|
CARTOGRAPHER_TOUCH
|
|
STATUS_READY
|
|
#--------------------------------------------------------------------
|
|
|
|
[gcode_macro PRINT_START]
|
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
|
gcode:
|
|
RESPOND MSG="🚦 Waiting for bed/chamber readiness..."
|
|
SET_MATERIAL {rawparams}
|
|
FAST_CALIBRATE {rawparams}
|
|
CLEAN_NOZZLE
|
|
STATUS_PRINTING
|
|
LINE_PURGE
|
|
|
|
[gcode_macro PRINT_END]
|
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
|
gcode:
|
|
M400 ; wait for buffer to clear
|
|
G92 E0 ; zero the extruder
|
|
G1 E-10.0 F3600 ; retract filament
|
|
G91 ; relative positioning
|
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
|
TURN_OFF_HEATERS
|
|
M107 ; turn off fan
|
|
M106 S0
|
|
G1 Z5 F3000 ; move nozzle up 5mm
|
|
G90 ; absolute positioning
|
|
BED_MESH_CLEAR
|
|
SET_PIN PIN=daylight VALUE=0.0
|
|
|
|
## Thermistor Types
|
|
## "EPCOS 100K B57560G104F"
|
|
## "ATC Semitec 104GT-2"
|
|
## "NTC 100K beta 3950"
|
|
## "Honeywell 100K 135-104LAG-J01"
|
|
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
|
## "AD595"
|
|
## "PT100 INA826"
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 15.921
|
|
#*# pid_ki = 3.553
|
|
#*# pid_kd = 12.717
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 38.431
|
|
#*# pid_ki = 1.601
|
|
#*# pid_kd = 230.586
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = -0.65
|
|
#*#
|
|
#*# [input_shaper]
|
|
#*# shaper_type_x = mzv
|
|
#*# shaper_freq_x = 52.2
|
|
#*# shaper_type_y = mzv
|
|
#*# shaper_freq_y = 37.8
|
|
#*#
|
|
#*# [scanner]
|
|
#*# mode = touch
|
|
#*# scanner_touch_threshold = 2250
|
|
#*# scanner_touch_speed = 3
|
|
#*#
|
|
#*# [scanner model default]
|
|
#*# model_coef = 1.503616458401332,
|
|
#*# 1.8307346475213917,
|
|
#*# 0.7262664387406956,
|
|
#*# 0.2835099604869052,
|
|
#*# 0.49907486591585376,
|
|
#*# 0.6866272569538326,
|
|
#*# -0.4090974133486076,
|
|
#*# -0.7852408625740519,
|
|
#*# 0.33079701878632656,
|
|
#*# 0.4362887326279605
|
|
#*# model_domain = 3.241918166319436e-07,3.3488126441795064e-07
|
|
#*# model_range = 0.200000,5.100000
|
|
#*# model_temp = 32.343261
|
|
#*# model_offset = 0.00000
|
|
#*# model_mode = touch
|
|
#*# model_fw_version = CARTOGRAPHER 5.1.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.072398, 0.066187, 0.119609, 0.134320, 0.132330, 0.124682, 0.100382, 0.086712, 0.077852, 0.074655
|
|
#*# 0.039626, 0.036818, 0.092077, 0.101400, 0.103115, 0.087366, 0.059710, 0.045081, 0.039742, 0.020377
|
|
#*# 0.007233, 0.011211, 0.055786, 0.061958, 0.054488, 0.046772, 0.017405, 0.006026, 0.001332, -0.019181
|
|
#*# -0.015451, -0.008911, 0.036741, 0.037070, 0.022559, 0.018322, -0.002258, -0.016678, -0.023943, -0.036462
|
|
#*# -0.032068, -0.040985, 0.033854, 0.035543, 0.009602, -0.000700, -0.021671, -0.027756, -0.038461, -0.058526
|
|
#*# -0.036397, -0.034285, 0.032927, 0.026578, -0.003679, -0.002466, -0.023670, -0.034656, -0.036612, -0.054150
|
|
#*# -0.021564, -0.030095, 0.022793, 0.029899, 0.010114, 0.000905, -0.013579, -0.025803, -0.025878, -0.035988
|
|
#*# 0.007332, 0.002438, 0.063747, 0.059245, 0.045247, 0.033976, 0.020512, 0.012343, 0.014880, -0.002763
|
|
#*# 0.044449, 0.033778, 0.080687, 0.087097, 0.085445, 0.074759, 0.065539, 0.054285, 0.054044, 0.039216
|
|
#*# 0.045665, 0.049666, 0.111007, 0.114869, 0.103424, 0.098449, 0.091647, 0.084339, 0.083037, 0.062745
|
|
#*# x_count = 10
|
|
#*# y_count = 10
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 15.0
|
|
#*# max_x = 334.95
|
|
#*# min_y = 25.0
|
|
#*# max_y = 334.96
|