175 lines
6.0 KiB
INI
175 lines
6.0 KiB
INI
# This file contains common pin mappings for the BigTreeTech OctoPus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[include ./TOOLHEAD/*.cfg]
|
|
[include ./SYSTEM/*.cfg]
|
|
[include ./CUSTOM/*.cfg]
|
|
|
|
[mcu]
|
|
## [X in MOTOR0] - B Motor
|
|
## [Y in MOTOR1] - A Motor
|
|
## [E in MOTOR6] - Extruder
|
|
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_360026001950534146373920-if00
|
|
restart_method: command
|
|
##--------------------------------------------------------------------
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 500
|
|
max_accel: 4200 #Max 4000
|
|
#max_y_accel: 4200
|
|
#max_x_accel: 8000
|
|
#max_accel: 10000 #Testing - revert back to above line after!
|
|
#max_accel_to_decel: 10000 #Testing - revert back to above line after!
|
|
max_z_velocity: 30 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 500
|
|
square_corner_velocity: 2.0
|
|
minimum_cruise_ratio: 0
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
[skew_correction]
|
|
[exclude_object]
|
|
[firmware_retraction]
|
|
[gcode_arcs]
|
|
resolution: 0.1
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
|
|
[gcode_macro G32]
|
|
description: Home XYZ mesh calibrate
|
|
gcode:
|
|
STATUS_HOMING
|
|
BED_MESH_CLEAR
|
|
G28
|
|
QUAD_GANTRY_LEVEL
|
|
STATUS_MESHING
|
|
BED_MESH_CALIBRATE
|
|
G1 X{ printer.toolhead.axis_maximum.x/2 } Y{ printer.toolhead.axis_maximum.y/2 } Z30 F4500
|
|
CARTOGRAPHER_TOUCH
|
|
STATUS_READY
|
|
#--------------------------------------------------------------------
|
|
|
|
[gcode_macro PRINT_START]
|
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
|
gcode:
|
|
RESPOND MSG="🚦 Waiting for bed/chamber readiness..."
|
|
SET_MATERIAL {rawparams}
|
|
FAST_CALIBRATE {rawparams}
|
|
CLEAN_NOZZLE
|
|
STATUS_PRINTING
|
|
LINE_PURGE
|
|
|
|
[gcode_macro PRINT_END]
|
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
|
gcode:
|
|
M400 ; wait for buffer to clear
|
|
G92 E0 ; zero the extruder
|
|
G1 E-10.0 F3600 ; retract filament
|
|
G91 ; relative positioning
|
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
|
TURN_OFF_HEATERS
|
|
M107 ; turn off fan
|
|
M106 S0
|
|
G1 Z5 F3000 ; move nozzle up 5mm
|
|
G90 ; absolute positioning
|
|
BED_MESH_CLEAR
|
|
SET_PIN PIN=daylight VALUE=0.0
|
|
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 15.921
|
|
#*# pid_ki = 3.553
|
|
#*# pid_kd = 12.717
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 38.431
|
|
#*# pid_ki = 1.601
|
|
#*# pid_kd = 230.586
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = -0.65
|
|
#*#
|
|
#*# [input_shaper]
|
|
#*# shaper_type_x = mzv
|
|
#*# shaper_freq_x = 52.2
|
|
#*# shaper_type_y = mzv
|
|
#*# shaper_freq_y = 37.8
|
|
#*#
|
|
#*# [scanner]
|
|
#*# mode = touch
|
|
#*# scanner_touch_threshold = 2500
|
|
#*# scanner_touch_speed = 3
|
|
#*#
|
|
#*# [scanner model default]
|
|
#*# model_coef = 1.503616458401332,
|
|
#*# 1.8307346475213917,
|
|
#*# 0.7262664387406956,
|
|
#*# 0.2835099604869052,
|
|
#*# 0.49907486591585376,
|
|
#*# 0.6866272569538326,
|
|
#*# -0.4090974133486076,
|
|
#*# -0.7852408625740519,
|
|
#*# 0.33079701878632656,
|
|
#*# 0.4362887326279605
|
|
#*# model_domain = 3.241918166319436e-07,3.3488126441795064e-07
|
|
#*# model_range = 0.200000,5.100000
|
|
#*# model_temp = 32.343261
|
|
#*# model_offset = -0.0250
|
|
#*# model_mode = touch
|
|
#*# model_fw_version = CARTOGRAPHER 5.1.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.072398, 0.066187, 0.119609, 0.134320, 0.132330, 0.124682, 0.100382, 0.086712, 0.077852, 0.074655
|
|
#*# 0.039626, 0.036818, 0.092077, 0.101400, 0.103115, 0.087366, 0.059710, 0.045081, 0.039742, 0.020377
|
|
#*# 0.007233, 0.011211, 0.055786, 0.061958, 0.054488, 0.046772, 0.017405, 0.006026, 0.001332, -0.019181
|
|
#*# -0.015451, -0.008911, 0.036741, 0.037070, 0.022559, 0.018322, -0.002258, -0.016678, -0.023943, -0.036462
|
|
#*# -0.032068, -0.040985, 0.033854, 0.035543, 0.009602, -0.000700, -0.021671, -0.027756, -0.038461, -0.058526
|
|
#*# -0.036397, -0.034285, 0.032927, 0.026578, -0.003679, -0.002466, -0.023670, -0.034656, -0.036612, -0.054150
|
|
#*# -0.021564, -0.030095, 0.022793, 0.029899, 0.010114, 0.000905, -0.013579, -0.025803, -0.025878, -0.035988
|
|
#*# 0.007332, 0.002438, 0.063747, 0.059245, 0.045247, 0.033976, 0.020512, 0.012343, 0.014880, -0.002763
|
|
#*# 0.044449, 0.033778, 0.080687, 0.087097, 0.085445, 0.074759, 0.065539, 0.054285, 0.054044, 0.039216
|
|
#*# 0.045665, 0.049666, 0.111007, 0.114869, 0.103424, 0.098449, 0.091647, 0.084339, 0.083037, 0.062745
|
|
#*# x_count = 10
|
|
#*# y_count = 10
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 15.0
|
|
#*# max_x = 334.95
|
|
#*# min_y = 25.0
|
|
#*# max_y = 334.96
|