New Backup on boot - 16/04/25 - 14:15:33

2025-04-16 14:15:36 +01:00
commit 73be850f66
@@ -0,0 +1,77 @@
+# This file contains common pin mappings for the BIGTREETECH EBB USB board.
+# To use this config, the firmware should be compiled for the RP2040 with "USB".
+# The "EBB Can" micro-controller will be used to control the components on the nozzle.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[mcu EBB]
+serial: /dev/serial/by-id/usb-Klipper_rp2040_5044340310A5581C-if00
+
+[temperature_sensor EBB_NTC]
+sensor_type: Generic 3950
+sensor_pin: EBB:gpio27
+
+[lis2dw]
+cs_pin: EBB:gpio1
+spi_bus: spi0a
+axes_map: z,x,y
+
+[resonance_tester]
+probe_points: 175, 175, 20
+accel_chip: lis2dw
+
+[extruder]
+step_pin: EBB:gpio18
+dir_pin: !EBB:gpio19
+enable_pin: !EBB:gpio17
+gear_ratio: 50:10
+microsteps: 16
+rotation_distance: 22.6789511
+full_steps_per_rotation: 200
+nozzle_diameter: 0.600
+filament_diameter: 1.750
+heater_pin: EBB:gpio7
+pullup_resistor: 2200 # 2.2K
+sensor_type: PT1000
+sensor_pin: EBB:gpio26
+max_extrude_cross_section: 5
+min_temp: 0
+max_temp: 350
+
+#sensor_type: MAX31865
+#sensor_pin: EBB:gpio9
+#spi_bus: spi1a
+#rtd_nominal_r: 1000
+#rtd_reference_r: 4300
+#rtd_num_of_wires: 2
+#rtd_use_50Hz_filter: True
+
+[tmc2209 extruder]
+uart_pin: EBB:gpio20
+run_current: 0.650
+stealthchop_threshold: 999999
+
+#[fan] # fan1
+#pin: EBB:gpio14
+
+[heater_fan hotend_fan] # fan2
+pin: EBB:gpio14
+heater: extruder
+heater_temp: 50.0
+
+#[fan_generic fan3]
+#pin: EBB:gpio5
+
+#[fan_generic 4W_FAN]
+#pin: EBB:gpio16
+#tachometer_pin: EBB:gpio12
+#tachometer_ppr: 1
+
+[filament_switch_sensor toolhead_switch_sensor]
+switch_pin: EBB:gpio13
+pause_on_runout: True
+runout_gcode:
+  PAUSE # [pause_resume] is required in printer.cfg
+  M117 Toolhead Filament switch runout
+insert_gcode:
+  M117 Toolhead Filament switch inserted
@@ -0,0 +1,31 @@
+
+[mcu eddy]
+serial: /dev/serial/by-id/usb-Klipper_rp2040_504450612086291C-if00 # This is the serial address of your eddy probe. This can be found by using the terminal of your klipper instance (typically through SSH) and using the command ```ls /dev/serial/by-id``` 
+restart_method: command
+
+[probe_eddy_ng btt_eddy]
+sensor_type: btt_eddy
+i2c_mcu: eddy
+i2c_bus: i2c0f
+x_offset: 0 # INSERT VALUE FOR YOUR PROBE POSITION
+y_offset: 36 # INSERT VALUE FOR YOUR PROBE POSITION 
+reg_drive_current: 15
+tap_target_z: -0.6
+tap_start_z: 3
+tap_mode: butter
+tap_threshold: 135
+tap_samples: 5
+tap_max_samples: 10
+tap_samples_stddev: 0.025
+tap_speed: 2
+tap_adjust_z: -0.225
+
+[temperature_sensor btt_eddy_mcu]
+sensor_type: temperature_mcu
+sensor_mcu: eddy
+min_temp: 10
+max_temp: 100
+
+[temperature_sensor btt_eddy]
+sensor_type: Generic 3950
+sensor_pin: eddy:gpio26
@@ -0,0 +1,19 @@
+[filament_switch_sensor switch_sensor]
+switch_pin: ^PG10
+pause_on_runout: True
+runout_gcode:
+  PAUSE # [pause_resume] is required in printer.cfg
+  M117 Filament switch runout
+insert_gcode:
+  M117 Filament switch inserted
+
+[filament_motion_sensor encoder_sensor]
+switch_pin: ^PG11
+detection_length: 5.0 #2.88 minimum
+extruder: extruder
+pause_on_runout: True
+runout_gcode:
+  PAUSE # [pause_resume] is required in printer.cfg
+  M117 Filament encoder runout
+insert_gcode:
+  M117 Filament encoder inserted