printer.cfg modified - 19/04/25 - 14:51:18
This commit is contained in:
pi committed
1 parent
8adbeb80e2
commit
f599688113
1 file changed
-162
@@ -56,168 +56,6 @@ enable_force_move: True
|
|||||||
[gcode_arcs]
|
[gcode_arcs]
|
||||||
resolution: 0.1
|
resolution: 0.1
|
||||||
|
|
||||||
|
|
||||||
#####################################################################
|
|
||||||
# X/Y Stepper Settings
|
|
||||||
#####################################################################
|
|
||||||
|
|
||||||
## X Stepper on MOTOR0(B Motor)
|
|
||||||
[stepper_x]
|
|
||||||
step_pin: PF13
|
|
||||||
dir_pin: PF12
|
|
||||||
enable_pin: !PF14
|
|
||||||
rotation_distance: 40
|
|
||||||
microsteps: 16
|
|
||||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
||||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
||||||
position_min: 0
|
|
||||||
position_endstop: 352
|
|
||||||
position_max: 352
|
|
||||||
|
|
||||||
##--------------------------------------------------------------------
|
|
||||||
homing_speed: 50 #Max 100
|
|
||||||
homing_retract_dist: 0
|
|
||||||
homing_positive_dir: true
|
|
||||||
|
|
||||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
||||||
[tmc2209 stepper_x]
|
|
||||||
uart_pin: PC4
|
|
||||||
interpolate: False
|
|
||||||
run_current: 0.9
|
|
||||||
hold_current: 0.7
|
|
||||||
sense_resistor: 0.110
|
|
||||||
#stealthchop_threshold: 400
|
|
||||||
diag_pin: ^PG6
|
|
||||||
driver_SGTHRS: 60 #255 Most Sensitive 0 Least Sensitive
|
|
||||||
|
|
||||||
## Y Stepper on MOTOR1 (A Motor)
|
|
||||||
[stepper_y]
|
|
||||||
step_pin: PG0
|
|
||||||
dir_pin: PG1
|
|
||||||
enable_pin: !PF15
|
|
||||||
rotation_distance: 40
|
|
||||||
microsteps: 16
|
|
||||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
||||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
||||||
position_min: 0
|
|
||||||
position_endstop: 359
|
|
||||||
position_max: 359
|
|
||||||
|
|
||||||
##--------------------------------------------------------------------
|
|
||||||
homing_speed: 50 #Max 100
|
|
||||||
homing_retract_dist: 0
|
|
||||||
homing_positive_dir: true
|
|
||||||
|
|
||||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
||||||
[tmc2209 stepper_y]
|
|
||||||
uart_pin: PD11
|
|
||||||
interpolate: False
|
|
||||||
run_current: 0.9
|
|
||||||
hold_current: 0.7
|
|
||||||
sense_resistor: 0.110
|
|
||||||
#stealthchop_threshold: 400
|
|
||||||
diag_pin: ^PG9
|
|
||||||
driver_SGTHRS: 63 #255 Most Sensitive 0 Least Sensitive
|
|
||||||
|
|
||||||
#####################################################################
|
|
||||||
# Z Stepper Settings
|
|
||||||
#####################################################################
|
|
||||||
|
|
||||||
## Z0 Stepper - Front Left on MOTOR2_1
|
|
||||||
[stepper_z]
|
|
||||||
step_pin: PF9
|
|
||||||
dir_pin: PF10
|
|
||||||
enable_pin: !PG2
|
|
||||||
rotation_distance: 40
|
|
||||||
gear_ratio: 80:16
|
|
||||||
microsteps: 16
|
|
||||||
#endstop_pin: probe:z_virtual_endstop
|
|
||||||
endstop_pin: EBB:gpio6
|
|
||||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
||||||
## (+) value = endstop above Z0, (-) value = endstop below
|
|
||||||
## Increasing position_endstop brings nozzle closer to the bed
|
|
||||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
||||||
#position_endstop: -0.5
|
|
||||||
##--------------------------------------------------------------------
|
|
||||||
|
|
||||||
## Uncomment below for 250mm build
|
|
||||||
#position_max: 240
|
|
||||||
|
|
||||||
## Uncomment below for 300mm build
|
|
||||||
#position_max: 290
|
|
||||||
|
|
||||||
## Uncomment below for 350mm build
|
|
||||||
position_max: 300
|
|
||||||
|
|
||||||
##--------------------------------------------------------------------
|
|
||||||
position_min: -1
|
|
||||||
homing_speed: 10
|
|
||||||
second_homing_speed: 1
|
|
||||||
homing_retract_dist: 2
|
|
||||||
|
|
||||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
||||||
[tmc2209 stepper_z]
|
|
||||||
uart_pin: PF2
|
|
||||||
interpolate: true
|
|
||||||
run_current: 0.8
|
|
||||||
hold_current: 0.8
|
|
||||||
sense_resistor: 0.110
|
|
||||||
stealthchop_threshold: 0
|
|
||||||
|
|
||||||
## Z1 Stepper - Rear Left on MOTOR3
|
|
||||||
[stepper_z1]
|
|
||||||
step_pin: PC13
|
|
||||||
dir_pin: !PF0
|
|
||||||
enable_pin: !PF1
|
|
||||||
rotation_distance: 40
|
|
||||||
gear_ratio: 80:16
|
|
||||||
microsteps: 16
|
|
||||||
|
|
||||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
||||||
[tmc2209 stepper_z1]
|
|
||||||
uart_pin: PE4
|
|
||||||
interpolate: true
|
|
||||||
run_current: 0.8
|
|
||||||
hold_current: 0.8
|
|
||||||
sense_resistor: 0.110
|
|
||||||
stealthchop_threshold: 0
|
|
||||||
|
|
||||||
## Z2 Stepper - Rear Right on MOTOR4
|
|
||||||
[stepper_z2]
|
|
||||||
step_pin: PE2
|
|
||||||
dir_pin: PE3
|
|
||||||
enable_pin: !PD4
|
|
||||||
rotation_distance: 40
|
|
||||||
gear_ratio: 80:16
|
|
||||||
microsteps: 16
|
|
||||||
|
|
||||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
||||||
[tmc2209 stepper_z2]
|
|
||||||
uart_pin: PE1
|
|
||||||
interpolate: true
|
|
||||||
run_current: 0.8
|
|
||||||
hold_current: 0.80
|
|
||||||
sense_resistor: 0.110
|
|
||||||
stealthchop_threshold: 0
|
|
||||||
|
|
||||||
## Z3 Stepper - Front Right on MOTOR5
|
|
||||||
[stepper_z3]
|
|
||||||
step_pin: PE6
|
|
||||||
dir_pin: !PA14
|
|
||||||
enable_pin: !PE0
|
|
||||||
rotation_distance: 40
|
|
||||||
gear_ratio: 80:16
|
|
||||||
microsteps: 16
|
|
||||||
|
|
||||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
||||||
[tmc2209 stepper_z3]
|
|
||||||
uart_pin: PD3
|
|
||||||
interpolate: true
|
|
||||||
run_current: 0.8
|
|
||||||
hold_current: 0.80
|
|
||||||
sense_resistor: 0.110
|
|
||||||
stealthchop_threshold: 0
|
|
||||||
|
|
||||||
#####################################################################
|
#####################################################################
|
||||||
# Bed Heater
|
# Bed Heater
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|||||||
Reference in new issue
Block a user